Sharp XL-HF200PH(S) MP3 Docking Station User Manual


 
10/5/26 XL-HF200PH(S)(BK)_AUS.fm
6
8
7
6
5
4
3
2
1
General control
Press the ON/STAND-BY button to turn the power on.
To dim the display brightness, press the DEMO/DIMMER button on
the remote control.
When the power is turned on, volume illuminator lights up.
To turn on/off the light, hold down the DEMO/DIMMER button on
the remote control for more than 2 seconds.
If you turn off and on the main unit with the volume set to 27 or higher,
the volume starts at 16 and fades in to the last set level.
Turn the volume knob towards VOL +/– (on main unit) or press
VOLUME +/– (on remote control) to increase or decrease the
volume.
When you press any of the following buttons, the unit turns on.
iPod / iPhone, CD, USB, AUDIO / LINE (INPUT), TUNER (BAND)
on the remote control: Selected function is activated.
/ button on the main unit: The unit turns on and playback of
the last function will start (CD, TUNER, USB, iPod, AUDIO IN,
LINE IN)
The main unit will enter the stand-by mode (when iPod/iPhone is not
docked) after 15 minutes of inactivity during:
iPod/iPhone: No connection.
AUDIO IN / LINE IN: No detection of input signal or very low sound
audibility.
TUNER: No reception of broadcast signal.
CD / USB: In the stop mode.
Note:
However, if iPod/iPhone is docked, the unit will begin charging.
“Charge Mode” will be displayed.
The volume is muted temporarily when pressing the MUTE button on
the remote control. Press again to restore the volume.
When the power is first turned on, the unit will enter the extra bass
mode which emphasises the bass frequencies, and “X-BASS” will
appear. To cancel the extra bass mode, press the X-BASS button on
the remote control.
1
Press the BASS/TREBLE button to select “BASS”.
2
Within 5 seconds, press the VOLUME (+ or –) button to adjust the
bass.
1
Press the BASS/TREBLE button to select “TREBLE”.
2
Within 5 seconds, press the VOLUME (+ or –) button to adjust the
treble.
When the FUNCTION button on main unit is pressed, the current
function will change to different mode. Press the FUNCTION button
repeatedly to select desired function.
Note:
The backup function will protect the memorised function mode for a
few hours should there be a power failure or the AC power lead
becomes disconnected.
Setting the clock (
Remote
control only)
In this example, the clock is set for the 24-hour (00:00) display.
To turn the power on
After use:
Press the ON/STAND-BY button to enter the power stand-by mode.
Display brightness control
Volume illuminator
Volume auto fade-in
Volume control
Auto power on function
Auto power off function
Muting
RRMCGA22
RRMCGA2 25AWSA
Volume
Illuminator
Dimmer 1
Dimmer 2
Dimmer off
(Display is dim).
(Display gets dimmer).
(Display is bright).
X-Bass control
Bass control
Treble control
Equaliser
Function
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the ENTER button. To adjust the day,
press the or button and then press the ENTER button.
4
Press the or button to select 24-hour or 12-hour display
and then press the ENTER button.
The 24-hour display will appear.
(00:00 - 23:59)
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 00:00 - PM 11:59)
Pops
Vocal
Jazz
Flat
Game
Classic
Equaliser off.
For game.
For classical music.
For pop music.
Vocals are enhanced.
For jazz.
When the EQUALIZER MODE
button is pressed, the current
mode setting will be displayed. To
change to a different mode, press
the EQUALIZER MODE button
repeatedly until the desired
sound mode appears.
FM STEREO
FM MONO
USB
iPod
Audio In
Line In
CD AM
RRMCGA 225AWSA