Filter
Top Products
SWITCHING ON AND OFF
1. Press STANDBY ON
y
to switch on.
2. Press the
Source selector
once or more to select
your desired function:
CD, FM, MW, GAME AUX.
(or press CD, FM, MW, AUX on the remote control)
3. Press STANDBY ON
y
to switch off.
Helpful Hints:
– The tone, sound settings, tuner presets and the
volume level (up to a maximum volume level of
VOL 20 ) will be retained in the set's memory.
ADJUSTING VOLUME AND SOUND (See 2)
• Adjust the volume with the VOLUME control.
= Display shows the volume level and a
number from 0-32.
MAX SOUND
To enhance the bass response: press MAX SOUND
once or more to switch on / off.
= MAX SOUND-key backlight lights up when
MAX SOUND is turned on.
Helpful Hints:
– MAX SOUND can be used when you play FM,
MW, CD and GAME
AUX source.
– Some discs might be recorded in high modulation,
which causes a distortion at high volume. If this
occurs, deactivate MAX SOUND or reduce the
volume.
EQUALIZER
1. To adjust the bass, mid and treble frequencies
press EQUALIZER once or more;
2. Rotate VOLUME within 3 seconds to adjust each
level.
= Display briefly shows
,
, or
level (-5 to +5) or .
Helpful Hints:
– EQUALIZER can be used during FM, MW, CD
and GAME
AUX source.
– To prevent sound interference the bass control
options operate exclusively. You cannot combine the
bass from EQUALIZER with MAX SOUND.
GAMESOUND
To adjust the game sound, press GAMESOUND once
or more to select your option.
= Display briefly shows
, ,
or
.
Helpful Hints:
– GAMESOUND is only available when you play in
GAME AUX source.
How to MUTE the sound
1. Press MUTE on the remote control to interrupt
sound reproduction instantly.
= Playback continues without sound and the
display flashes .
2. To reactivate sound reproduction you can:
– press MUTE again;
– adjust the volume controls;
– change to another source.
BASIC FUNCTIONS
This set complies with the radio interference requirements of the
European Union.
Tuning to stations (See 3)
1. Press STANDBY ON
y
to on, then press
Source
selector
once or more to select
FM/MW
(or press
FM/MW
on the remote control).
= Display: shows briefly followed by
waveband, frequency, and preset station
number if already stored.
2. Tuning to stations: you can tune to your
stations manually or by automatic search tuning:
Press down on
∞ or §
(
5 or 6
on the remote
control) and release button when the frequency in
the display starts running.
= The radio automatically tunes to a station of
sufficient reception. Display shows
during automatic tuning.
3. Repeat step 2 if necessary until you find the
desired station.
•To tune to a weak station, press
∞ or §
briefly
and repeatedly until you have found optimal
reception.
Helpful Hints:
To improve radio reception:
– For FM, extend, incline and turn the telescopic
antenna. Reduce its length if the signal is too
strong.
– For MW, the set uses a built-in antenna. Direct this
antenna by turning the whole set.
Programming tuner stations:
You can store up to a total of 30 radio stations in the
memory, manually or automatically (Autostore).
Autostore
Automatic programming will start from preset 1 or a
chosen preset number. The set will only program sta-
tions which are not in the memory already.
1. Press
ALBUM/PRESET -/+
once or more to
select the preset number where programming
should start.
Helpful Hints:
– If no tuner preset number is selected, default is
preset 1 and all your presets will be erased.
2. Press PROG for 4 seconds or more to activate
auto store programming.
= Display: is shown and available
stations are programmed in order of waveband
FM, followed by MW.
3. The first preset station will then be played after all
stations are stored automatically.
Manual programming
1. Tune to your desired station (see Tuning to
stations).
2. Press PROG to activate programming.
= Display: program flashes.
3. Press
ALBUM/PRESET -/+
once or more to
allocate a number from 1 to 30 to this stations.
4. Press PROG again to confirm.
= Display: shows the preset number, waveband
and the frequency of the preset station.
DIGITAL TUNER