Filter
Top Products
RESUME
You can interrupt playback and continue (even after an
extended period of time) from the position where playb-
ack stopped (RESUME) and you can lock all buttons of
the set so that no action will be executed (HOLD). Use
the RESUME–HOLD–OFF slider for these functions.
1 Switch the slider to RESUME during playback to
activate RESUME.
y
RESUME is shown.
2 Press 9 whenever you want to stop playback.
3 Press 2; whenever you want to resume playback.
yRESUME is shown and playback continues from
where you have stopped last.
• To deactivate RESUME, switch the slider to OFF.
y
RESUME goes off.
HOLD
You can lock the buttons of the set by switching the
slider to HOLD. Now, when a key is pressed, no action
will be executed. This is of use, for example, when trans-
porting the player in a bag. With HOLD activated, you can
avoid accidental activation of other functions.
1 Switch the slider to HOLD to activate HOLD.
yAll buttons are locked. HoLd is shown when
you press any button. If the set is switched off,
HoLd will be shown only when 2; is pressed.
2 To deactivate HOLD, switch the slider to OFF.
Note: If you deactivate
HOLD
by switching the slider to
RESUME,
you will be activating the
RESUME
function.
p
/
L
I
N
E
O
U
T
O
F
F
R
E
S
U
M
E
H
O
L
D
p
/
L
I
N
E
O
U
T
O
F
F
R
E
S
U
M
E
H
O
L
D
NOTES
p
/
L
I
N
E
O
U
T
p
/
L
I
N
E
O
U
T
TROUBLESHOOTING
WARNING:
Under no circumstances should you try to repair the set yourself as
this will invalidate the guarantee. If a fault occurs, first check the points listed
before taking the unit for repair. If you are unable to solve a problem by following
these hints, consult your dealer or service centre.
The CD player has no power, or playback does not start
• Check that your batteries are not dead or empty, that they are inserted
correctly, that the contact pins are clean.
• Your adapter connection may be loose. Connect it securely.
The indication no diSC is displayed
• Check that the CD is clean and correctly inserted (label-side upward).
• If your lens has steamed up, wait a few minutes for this to clear.
The indication nF diSC is displayed
• CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.
The indication
HOLD is on and/or there is no reaction to controls
• If HOLD is activated, then deactivate it.
• Electrostatic discharge. Disconnect power or remove batteries for a few seconds.
The CD skips tracks
• The CD is damaged or dirty. Replace or clean the CD.
• RESUME, SHUFFLE or PROGRAMis active. Switch off whichever is on.
No sound or bad sound quality.
• PAUSE might be active. Press 2;.
• Loose, wrong or dirty connections. Check and clean connections.
• Volume might not be appropriately adjusted. Adjust the volume.
• Strong magnetic fields. Check player’s position and connections. Also keep
away from active mobile phones.
MODE
It is possible to play tracks in random order, to repeat a
single track or the entire CD.
1 Press MODE during playback as often as required in
order to activate one of the following ‘modes’. The
active mode is shown in the display.
y
SHUFFLE: All tracks of the CD are played in random
order until all of them have been played once.
y
SHUFFLEREPEATALL
: All tracks of the CD are played
repeatedly in random order.
yREPEAT: The current track is played repeatedly.
y
REPEAT ALL: The entire CD is played repeatedly.
2 Playback starts in the chosen mode after 2 seconds.
• To return to normal playback, press MODE repeatedly
until the display shows no active modes.
MODE
PROGRAM