Filter
Top Products
1514
Follow the procedure below to set the user ID number:
MENU
ERASE SP DICT
ERASE SP DICT
INDEX/
FOLDER
MENU
ERASE SP DICT
INDEX/
FOLDER
MENU
ᕃ
ᕄ
ᕅ ᕆ
ᕃ
In the Stop mode, press and hold the MENU switch
µ
for at least 2 seconds. The menu will be dis-
played on the LCD panel
ᕣ
.
ᕄ
twice the MENU switch's up/down control in the down direction to display [ID AAA] (when in the ini-
tial setting). The cursor will start blinking at the first digit's position.
ᕅ
Turn the MENU switch's up/down control in the up direction to change the character displayed: [A]
Ǟ [B] Ǟ [C]
……
[X] Ǟ [Y] Ǟ [Z] Ǟ [0] Ǟ [1] Ǟ [2] Ǟ
……
[7] Ǟ [8] Ǟ [9] Ǟ [A] Ǟ [B]
……
ᕆ
When the desired character is displayed, press the MENU switch to set it. The blinking cursor
moves to the next position.
ᕇ
Follow the same procedure to set each character. When ID setting is complete, press the MENU
switch to enter the Format mode. (See page 31.)
ᕈ
Pressing the STOP button instead of the MENU switch after ID setting ends menu setting and
restores the Stop mode.
t
If the Format mode is entered in
ᕇ
but you do not need to format the built-in memory, press the
STOP button. This ends menu setting and restores the Stop mode.
ᕃ
Make sure [NEW], memory remaining time, and the message number are displayed on the LCD
panel. Ensure there is sufficient remaining time available for your message and select the folder
([A] or [B]), microphone sensitivity ([DICT] or [CONF]) and recording mode ([SP] and [LP]).
ᕄ
To change the folder, press the INDEX/FOLDER button
ᕢ
to move to the position after the last
recording in the other folder. To change the microphone sensitivity or recording mode, use the
menu (see page 29 for the change procedure).
ᕅ
Press the REC button
ᕡ
to start recording. The LED
ᕥ
lights and recording starts.
ᕆ
Press the STOP button to stop recording and enter the Stop mode.
ᕇ
You can monitor what is being recorded through an earphone plugged into the EAR jack
ᕧ
(recording monitor).
t
If [NEW] is not displayed when you press the REC button, insertion recording will start. This over-
writes the previous recording so be sure you always check the display before pressing the REC
button.
t
If [FULL] is displayed on the LCD panel, additional recording is not possible. In this case, erase
unnecessary messages to free up more memory. If there are any messages that you want to pre-
serve, transfer the voice data to a PC using the PC transfer kit (available as a standard or optional
accessory).
t
Do not connect or disconnect the AC adapter plug during recording. Always enter the Stop mode
before plugging or unplugging the adapter. Otherwise, you will not be able to play back the mes-
sage being recorded.
t
The recording monitor volume cannot be adjusted.
t
Always use the SP mode if you want to record high-quality voice data suitable for transfer to a PC
for use in voice recognition operations.
(For more about voice recognition, see page 33.)
BASIC OPERATION
RECORDING
ᕃ
REC STOP
INDEX/
FOLDER
ᕄ ᕅ ᕆ
Remaining
memory time
Message No.
T572 Inst DS-150-E.Q33J 1999/4/26 0:57 PM y[W 14