Filter
Top Products
E 5 E 6
POWER SUPPLY
This unit works with AC 120V, 60 Hz.
Connect AC power cable to wall outlet with 120V supply.
Insert two AAA 1.5V batteries into battery compartment for time back up in case of
power failure.
1.
2.
RADIO OPERATION
Press POWER button .
Set FUNCTION switch to RADIO position.
Tune to your desired station with TUNING Control .
Adjust VOLUME to suit your personal listening preference.
To turn off the unit, press POWER button again.
1.
2.
3.
4.
5.
ANTENNA
This unit has a built-in Ferrite Antenna. For best results - turn unit to improve reception.
For FM reception, fully extend the external FM wire antenna and adjust direction for
optimum reception. Do not connect this wire to any outdoor antenna.
AM:
FM:
CD OPERATION
This unit is capable of playing standard CDs.
Press POWER button .
Select FUNCTION switch to CD position.
Lift up the CD door open lid to open CD door.
Insert a CD disc in the CD compartment with label facing upwards.
Close the CD door. The total number of tracks will be displayed. If a disc is inserted
incorrectly, dirty, damaged or not music CD - display will show “nocd” and player will stop.
Press PLAY/PAUSE button to begin playback.
Press STOP button to stop playback.
PAUSE
The PLAYBACK can be stopped temporarily at any time by pressing PLAY/PAUSE button
once. Press PLAY/PAUSE button once more to resume playback.
1.
2.
3.
4.
5.
6.
7.
FORWARD/BACKWARD/SKIP
Press SKIP FORWARD button to skip ahead to the beginning of the next track.
Press this button again for each additional track you want to skip.
Press SKIP BACKWARD button to skip back to beginning of the current track.
Press this button again to the beginning of the previous track.
1.
2.
PROGRAM
The programming function is used to pre-set the order of the tracks to be played.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
RANDOM/REPEAT
DISPLAY
In CD or RADIO mode, press the DISPLAY button, the display will shown the number of
current track and the current station.
AUX IN
The CD player can play “RANDOM”, “REP.”, “REP. ALL” and “RANDOM REP. ALL” by press
RANDOM/REPEAT button repeatedly.
Press the POWER button.
Set the FUNCTION switch to the CD position.
Lift up the CD door lid in order to open the CD door.
Insert the CD, with the label facing upward.
Close the CD door. The total number of tracks on the CD will be shown on the display. If
the disc is inserted incorrectly, or if it is dirty or damaged, or if it is not a music CD, the
display will show nocd , and the player will stop.
Press the PROG. button. The “01 ” and “PROG ” icon will be shown on the display, and
will be blinking.
Press the SKIP / button in order to choose the track that you would like to play.
Press the PROG. button again in order to finish the programming for the first track.
Repeat step “ 7 ” in order to program the other tracks. A maximum of 20 tracks can be
programmed.
To clear the program memory, press the STOP button
Once you have finished programming, press the PLAY/PAUSE button . The tracks will
play in the programmed order, and the corresponding track number will be displayed.
You can move forward and backwards through the programmed tracks (see Forward/
Backward/SKIP), or temporarily stop playback (see Pause). To stop playback, press the
STOP button .
Note: Pressing the SKIP or button during programmed playback
will only skip through the tracks that have been programmed.
You can connect an external audio player to this jack in order to use the playback function.
Note: When a device is connected to the AUX IN jack, the current source from the CD or
RADIO will be cut off automatically.