Jensen JCR-332 Clock Radio User Manual


  Open as PDF
of 5
 
1
st
Alarm (AL 1)
1. Press the AL 1 Button (9) once, the display blinks for a few seconds and the AL 1
Indicator (21) will light up.
2. When the Display blinks, press MIN and HOUR Button (11) to adjust the alarm time.
3. Press the AL 1 Button (9) again to memorize the alarm time. The Display (17) will resume
to clock time.
2
nd
Alarm (AL 2)
1. Press the AL 2 Button (10) once, the display will blink for a few seconds and the AL 2
Indicator (22) will light up.
2. When the Display blinks, press MIN and HOUR Button (11) to adjust the alarm time.
3. Press the AL 2 Button (10) again to memorize the alarm time. The Display (17) will
resume to clock time.
NOTE
There is a PM INDICATOR located in the top left-hand corner of the clock display. Be sure
to observe the PM Indicator when setting the alarm to make sure the alarm time is set
correctly for AM or PM. If the PM Indicator is ‘On’, the alarm time will be “PM”. If the PM
Indicator is ‘off’, the alarm time will be “AM”.
76
STOPPING THE ALARM
The JCR-332 allows you to set two different wake up times which you can choose to use
independently, as ALARM 1 or as ALARM 2 or simultaneously together.
LISTENNING TO THE EXTERNAL DEVICE (AUX)
THIS UNIT FEATURES AN AUX LINE-IN JACK FOR CONNECTING YOUR i-Pod, MP3
PLAYER OR OTHER DIGITAL MUSIC PLAYER.
1. Connect the headphone jack of your external device to the AUX LINE-IN jack (16) located
on the back of the JCR-332 (cable not included).
2. Turn on the JCR-332 and it will enter the AUX function mode once an external device is
plugged into the AUX LINE-IN jack.
3. Start playing your i-Pod, MP3 player or other external audio device.
4. Slowly adjust both volume controls on the JCR-332 and the external device.
5. Turn off your i-Pod, MP3 player etc. when finish listening. Turn the JCR-332 off and
unplug the AUX LINE-IN jack.
Remark: Once an AUX LINE-IN jack is plugged during POWER ON mode, it will automati-
cally enter the AUX mode no matter what position the FUNCTION Selector (30) is in. Re-
member to disconnect the cable from the JCR-332 after use in order to be able to listen to
the radio or CD player again.
The alarm is programmed to run for 60 minutes.
1. Press the SNOOZE Button (2) to stop the alarm temporarily. The alarm will stop and
sound again automatically after 6 minutes.
2. Press the ON / OFF Button (1) once, the alarm will stop, and will sound again 24 hours
later.
3. To turn the alarm off permanently, press the AL1 / AL2 Button (9 / 10) repeatedly until the
Alarm LED Indicators (21 / 22) go off.
OPERATING THE ALARM AND WAKE UP MODE
To set your own musical program.
1. Insert the disc. The total number of tracks is displayed in the LED Display
(17).
2. Press Button (8) once, the display shows ‘ ’ for 2 seconds, and then
“ ” blinks along with the PROGRAM Indicator (25). Make sure your
player is in STOP mode.
3. Select your desired track with or (11), then press button (8) to store
your program in memory. Repeat this operation as many times as
necessary. Up to 20 tracks can be stored in the memory.
4. Press (5) to start playing.
5. Press (6) to stop the disc.
6. To cancel this function, open the CD door.
PROGRAM (8):
WAKE TO ALARM BUZZER
1. Set the FUNCTION Selector (30) to the Buzzer position.
2. The Alarm Indicator (21/ 22) will blink and the buzzer will sound when the alarm time is
reached. The buzzer will play for about one hour and then shut off automatically.
3. To stop the radio, press the ON/OFF Button (1). The Buzzer will stop but the alarm
remains set and will turn the unit on again at the same time on the following day.
4. If you do not want the alarm to turn the unit on the following day, press the AL1 or AL2
buttons once. The AL1 or AL2 Indicator (21/22) will go off.
WAKE TO RADIO
1. Follow procedures 1 to 7 in “LISTENING TO THE RADIO” to set your radio wake up mode.
2. The alarm indicator (21 / 22) will blink and the Radio will turn on when the alarm time is
reached. The Radio will play for about one hour and then shut off automatically.
3. To stop the Radio, press the ON/OFF Button (1) once. The Radio will stop, but the alarm
remains set and will turn the unit on again at the same time on the following day.
4. If you do not want the alarm to turn the unit on the following day, press the AL1 or AL2
buttons once. The AL1 or AL2 Indicator (21/22) will go off.
WAKE TO CD
1. Follow the procedure 1 to 6 in “LISTENING TO THE CD PLAYER”
2. Press the ON / OFF Button (1) to turn off the unit. The POWER Indicator (14) goes off.
3. The Alarm Indicator (21/ 22) will blink and the CD will play when the alarm time is reached.
Note: The “REPEAT ALL” function will be active automatically when in Wake To CD mode,
and it will play for 60 minutes continuously unless the alarm is stopped.
The unit will automatically change to buzzer alarm if a damaged CD or the CD is incorrectly
inserted.
Remark: If an external device is plugged into AUX LINE-IN jack during ALARM ON mode,
it will change to Buzzer mode automatically no matter what position the FUNCTION Selec-
tor (30) is in.
If you want to be woken by a CD or Radio, make sure that the AUX LINE-IN jack is not
plugged.
1. Select CD or Radio mode for sleep by setting the FUNCTION Selector (30) to the CD or
RADIO position.
2. Press the SLEEP Button (12). The display shows “ ” and the unit will go to the sleep mode.
3. Press the SLEEP Button (12) repeatedly to select the desired sleep time among 90, 60,
30 or 15 minutes.
4. The radio will automatically turn off when the sleep time has elapsed.
5. If “Sleep To CD” is selected, press the PLAY/PAUSE Button (5) to start playing and
playback will stop after the selected time is reached.
6. If you want to turn off the unit before the preset sleep time has elapsed simply press the
ON / OFF Button (1).
SLEEP TO MUSIC
2008-5-6, 11:504
 previous