Filter
Top Products
- Press once to go into repeat one mode, your selected track will play
repeatedly. REPEAT Indicator (24) blinks.
- Press twice to go into repeat all mode, the disc plays continuously. The
REPEAT Indicator (24) lights.
- Press three times to go into random play mode, press once to start
random play. The disc will play randomly. The REPEAT Indicator (24) will
go off and the RANDOM Indicator (23) will light.
- Press again to switch off this function, RANDOM Indicator (23) goes off.
SKIP / FAST SEARCH ( / ) (11): Press to skip forward to the next track or
repeatedly to skip tracks. Press to return to the beginning of the track, or press repeat-
edly to skip backward several tracks. Press and hold or to search quickly within a
track.
1. Press the OPEN Button (3) to open the CD door. Insert your CD (label up) into the
compartment (4).
2. Switch the FUNCTION Selector (30) to the CD position.
3. Press the ON / OFF Button (1) once, the POWER LED Indicator (14) will turn on. The
Display (17) will briefly show the total number of tracks on the disc and return to the clock
time after few seconds.
4. To view which track is playing, press the DISPLAY Button (13) once. The Display will
briefly show the track no. of the current track and then return to clock time.
5. Press (5) to start playback from the first track. The Display (17) will show ‘ ’ then
return to the clock time.
NOTE : The Button is also used to pause playing of a track. Press once to pause, press
once again to continue to play.
6. Rotate the Volume (29) to adjust to desired level.
7. Press STOP / CLOCK (6) to stop playback of the disc.
Important : After you finish using the CD player, make sure you turn off the power by
pressing the ON / OFF Button (1). The POWER LED Indicator (14) will go off.
NOTE : CD-Rs or CD-RWs playback capability in this player may vary depending on quality
of media, CD-Burner, speed of burning and application software.
The Battery Back-Up System ensures the clock and alarm settings will be retained during
AC power interruption.
NOTE: In order to preserve the battery life the display will not light during power disruption.
All clock settings will be kept in memory, however, the clock time may require adjustment
for exact accuracy. If no back-up battery is installed, the display will blink “ ” to indicate
that you have to reset the time and alarm settings.
BACKUP BATTERY INSTALLATION
1. Open the Battery Compartment Door and following the polarity diagram shown in the
Battery Compartment, connect one 9V DC battery (not included) onto the battery clip
inside the compartment. The battery only fits one way onto the connector, so ensure the
correct polarity prior to attaching.
2. Replace the Battery Compartment Door.
IMPORTANT: Be sure that the battery is installed correctly. Wrong polarity may damage
the unit.
3. For best performance and longer operating time, we recommend the use of an alkaline-
type battery.
4. If the unit is not to be used for an extended period of time, remove the battery. Old or
leaking battery can cause damage to the unit and will also void the warranty.
5. Do not dispose of battery in fire. Battery may leak or explode.
NOTE: An alkaline type battery is highly recommended for optimum performance and should
be replaced every 6 months for maximum back-up protection in the case of a power failure.
This clock displays the time in two formats, 12 hour (12H) or 24 hour (24H) and by default is
set to 12H format.
1. Connect the AC plug into the convenient standard AC outlet, the LED Display blinks.
2. Press MIN or HOUR Buttons (11) to adjust the hours and minutes respectively.
3. Press STOP / CLOCK Button (6) again to set the clock time and the LED Display will
stop blinking.
NOTE
There is a PM Indicator located in the top left-hand corner of the clock display. Be sure
to observe the PM Indicator when setting the time to make sure the time is set correctly for
AM or PM. If the PM Indicator is ‘On’, the time displayed is “PM”. If the PM Indicator is ‘Off’,
the time displayed is “AM”.
4. Press and hold the STOP / CLOCK Button (6) for 2 seconds to change the clock format
to “24H” if preferred. The LED Display will show “24H” for one second, then the clock
time will be shown in 24 hour format.
4 5
1. Set the FUNCTION Selector (30) to the RADIO position.
2. Set the BAND Selector (26) to either AM or FM. If the FM band is selected, you are able
to choose either Mono or Stereo with the FM Mode Selector (28).
3. Press the ON / OFF Button (1) to turn on the radio and the POWER LED Indicator (14)
will turn on.
4. Adjust the Volume (29) to the desired level.
5. Select your desired radio station using the TUNING Knob (27).
6. Reception: For FM, fully extend the antenna wire (32) and position the wire for best
reception. To receive a weak or noisy FM station, set the FM MODE Selector (28) to the
MONO position. The reception then may improve, but the sound is now monaural (MONO).
For AM, rotate the unit for best reception.
7. To turn the radio off, press the ON / OFF Button (1) and the POWER LED Indicator (14)
will go off.
PLAY MODE(7):
This CD clock radio operates on 120V ~ 60Hz household current. This unit also features a
9V DC battery back-up system for the clock settings (9V (006P) battery not included).
1. Insert the AC power cord (15) into a convenient standard AC wall outlet.
2. Follow the directions in the following section (Battery Back-up System) for steps on
installing the battery for the clock back-up.
BATTERY BACK-UP SYSTEM
POWER SUPPLY
SETTING THE TIME
LISTENING TO THE RADIO
LISTENING TO THE CD PLAYER
OTHER CD PLAYER FUNCTIONS
2008-5-6, 11:503