EAW AP6 Portable Speaker User Manual


  Open as PDF
of 4
 
Instructions/Installing the KF850z
NL8 and AP6 Upgrade Kits
The KF850z AP6 Upgrade Kit P/N 0006241 and the KF850z NL8 Upgrade Kit P/N 0006242 are available for the
KF850e loudspeaker. These two kits are the same but for the Electrical Assemblies.
Warning: Installation should only be done by an experienced technician. Improper installation may result
in damage to the equipment, injury or death.
1. Inventory the kit against the following bill of materials insuring the kit is complete.
EAW P/N Qty Description
804116 1 Driver-Cone (LC-1536)
102021 4 Screw 1/4-20 X 1-1/2 LG SHCS Blk
0005848 1 Horn/URE/H4532
0008726 1 Driver/Compression [DN20/3004-8]
102165 4 Screw/M6 X 14mm LG HHCS
105005 4 Washer/Flat 1/4
105004 8 Washer/Lock 1/4
0006004 2 Bracket/Horn [KF850z Upgrade Kit]
102016 6 Screw 1/4-20 X 1 LG PH PHMS Blk
105007 10 Washer/Flat 1/4 Blk
105008 10 Washer/Lock 1/4 Blk
102017 4 Screw 1/4-20 X1 SHCS Blk
804097 1 Driver-Cone [LC-1075]
0006008 1 Assembly/Phase Plug/Housing
0006005 1 Ring/Aperture/Wood/10” Mid [KF850z]
0006007 4 Screw 1/4-20 X 4-1/2 LG SHCS Blk
105033 4 Washer/Flat/M6
0006011 1 Instruction/Kit/KF850z/Upgrade
102087 4 Screw #8 X 1 LG PH PHSMS
102048 8 Screw #10 X 16 X 3/4 PH PHSMS
102102 23 Screw #8 X 5/8 PH PHSMS Blk
0006239 1 Electrical Assembly KF850z [NL8]
or
0006240 1 Electrical Assembly KF850z [AP6]
2. Overview
KF850z Kit installation requires the technician to remove and replace all transducer components. The HF
horn assembly is accessed from the front and the 15” woofer, 10” mid range, and electrical assembly from
the back.
To do this the enclosure will first be rested on its back, the grille
removed, and the HF horn assembly disconnected, removed, and dis-
assembled. Its rear bracket will be re-installed into the new KF850z
HF horn assembly, which will then be installed into the enclosure.
After this is complete the enclosure should be repositioned onto its
front, and the 2 access lids, polyfill, input and crossover removed, the
new crossover installed, and its leads routed to the appropriate cham-
bers. Then the new 15” woofer and the new mid assembly will be
installed. The old polyfill should be restapled into both chambers and
the new electrical assembly installed.
Finally the enclosure will be stood upright, HF leads connected, test-
ed for continuity, and access lids and grille reinstalled.
3. Instructions: Tip the enclosure on its back and remove the 23
Phillips head screws that mount the grille to the enclosure.
REMOVE AND DISCARD
23 #8 X 5/8 LG PHILLIPS
HEAD SHEET METAL SCREW
S
10X GRILL
FOAM RETAINERS
(DO NOT REMOVE)
next