Filter
Top Products
280-8003-00
DXZ648RMP 25
English
Operations Common to Each Mode
Dimmer control
You can setting the dimmer control “ON” or
“OFF”.
∗ The factory default setting is “ON”.
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [a] or [d] button to select “DIM-
MER”.
3. Turning the [ROTARY] knob clockwise or
counterclockwise and select “ON” or “OFF”.
4. Press the [T] button to return to the previous
mode.
Selecting the CONTRAST mode
∗ The factory default setting is “5”.
1. Press and hold the button [T] for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [a] or [d] button to select “CON-
TRAST”.
3. Turning the [ROTARY] knob to select from 1-
16.
4. Press the [T] button to return to the previous
mode.
Anti-theft indicator
The red Anti-theft indicator is a function for pre-
venting theft. When the DCP is removed from
the unit, this indicator blinks.
∗ The factory default setting is “OFF”.
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [a] or [d] button and select
“BLINK LED”.
3. Turning the [ROTARY] knob clockwise to set
this function “ON” or turn it counterclockwise
to switch this function “OFF”.
4. Press the [T] button to return to the previous
mode.
Setting LOW PASS FILTER
∗ The factory default setting is “LPF 120 Hz”.
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [a] or [d] button and select
“SUB-W LPF”.
3. Tur ning the [ROTARY] knob clockwise or
counterclockwise to select the setting. Each
time you turn the [ROTARY] knob, the setting
changes in the following order:
LPF REAR ➜ LPF 50 Hz ➜ LPF 80 Hz ➜
LPF 120 Hz
4. Press the [T] button to return to the previous
mode.
AUX function
This system has an external input jack so you
can listen to sounds and music from external
devices when connected to this unit.
Selecting AUX/TEL
You can listen to sounds and music from exter-
nal devices or your telephone calls from the
speakers when connected to this unit.
When TEL INT or External device is connected to
this unit, you can select TEL mode or AUX mode.
∗ The factory default setting is “AUX”.
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [a] or [d] button and select
“AUX/TEL”.
3. Tur ning the [ROTARY] knob clockwise or
counterclockwise as needed and select from
“AUX” or “TEL”.
● AUX :
AUX/TEL input cable is for external Audio input.
● TEL :
AUX/TEL input cable is for cellular phone au-
dio input.
4. Press the [T] button to return to the previous
mode.
Selecting AUX IN sensitivity
Make the following settings to select the sensi-
tivity when sounds from external devices con-
nected to this unit are difficult to hear even after
adjusting the volume.
∗ The factory default setting is “AUX MID”.
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [a] or [d] button and select
“AUX SENS”.
+DXZ648RMP-009-ENG 11/12/03, 8:39 PM25