Filter
Top Products
22 DXZ655MP
280-8146-00
English
3-1. Turn the [ROTARY] knob to select “ON” or
“OFF”.
●Setting the Subwoofer
You can set the subwoofer on or off.
∗ The factory default setting is “ON”.
2-1. Select “ SUB-W”.
3-1. Turn the [ROTARY] knob to select “ON” or
“OFF”.
●Setting LOW PASS FILTER
∗ The factory default setting is “THROUGH”.
∗ If subwoofer function is set “ON”, “LOW PASS
FILTER” can be selected.
2-1. Select “ SUB-W LPF”.
3-1. Turn the [ROTARY] knob to select the
setting. Each time you turn the [ROTARY]
knob, the setting changes in the following
order:
THROUGH ➜ 50 ➜ 80 ➜ 120
●Setting the external amplifier
∗ The factory default setting is “OFF”.
2-1. Select “ AMP CANCEL”.
3-1. Turn the [ROTARY] knob to select “ON” or
“OFF”.
• ON:
Use with connected AMP.
• OFF:
Use with inside AMP.
●Selecting AUX IN sensitivity
Make the following settings to select the
sensitivity when sounds from external devices
connected to this unit are difficult to hear even
after adjusting the volume.
∗ The factory default setting is “MID”.
2-1. Select “ AUX SENS”.
3-1. Turn the [ROTARY] knob to select “LOW”,
“MID” or “HIGH”.
●Performing a system check
This function allows you to perform a system
check from the adjust mode when required.
2-1. Select “ SYSTEM CHECK ”.
3-1. Press and hold the [ ] button for 1
second or longer.
“SYSTEM CHECK” appears in the display,
then the unit returns to the previous
operation mode.
∗ This setting item can be adjusted within the
range SPEED 1 to SPEED 6.
Adjust this setting item while viewing how the
appearance of the display changes.
● Dimmer level
You can adjust the reduced illumination level of
the dimmer.
∗ The factory default setting is “LV3”.
(Adjustment range is LV1 to LV5)
2-1. Select “ DIMMER LV”.
3-1. Turn the [ROTARY] knob to adjust the
reduced illumination level of the dimmer.
● LV1 to LV5:
The dimmer operation is performed
depending on the set level LV1 to LV5.
● OFF:
No dimmer operation is performed.
● Adjusting the display contrast
You can adjust the display contrast to match the
angle of installation of the unit.
∗ The factory default setting is “08”. (Adjustment level:
01 to 16)
2-1. Select “ CONTRAST”.
3-1. Turn the [ROTARY] knob to adjust the
contrast.
To change other settings
1. Press the [ADJ] button to switch to the
adjustment selection display.
2. Press the [a, d] lever upward or
downward to select the “item name”.
Each time the [a, d] lever is pressed up/
down, the item display changes in the
following order:
“BLINK LED” ↔ “SUB-W” ↔ “SUB-W
LPF” ↔ “AMP CANCEL” ↔ “AUX SENS”
↔ “SYSTEM CHECK”
3. Turn the [ROTARY] knob to select the
“desired setting item”.
∗ After completing settings, press the [ADJ]
button to return to the previous mode.
● Anti-theft indicator
The red Anti-theft indicator is a function for
preventing theft. When the DCP is removed
from the unit, this indicator blinks.
∗ The factory default setting is “OFF”.
2-1. Select “ BLINK LED”.
Operations Common to Each Mode