Campbell Hausfeld NS289500 Clock Radio User Manual


 
2
Protect your eyes and
ears. Wear Z87 safety
glasses, with side
shields. Wear hearing
protection. Employers
and users are responsible for
ensuring the user or anyone near
the nailer wears this safety
protection. Serious eye injury or
permanent hearing loss could
result.
Do not use a
check valve or
any other
fitting which
allows air to
remain in the
nailer. Death or serious personal
injury could occur.
Never place
hands or any
other body
parts in the nail
discharge area
of the nailer.
The nailer might
eject a fastener and could result in
death or serious personal injury.
Never carry the
nailer by the air
hose or pull the
hose to move the
nailer or a
compressor. Keep
hoses away from
heat, oil and sharp edges. Replace
any hose that is damaged, weak or
worn. Personal injury or tool
damage could occur.
Always assume the nailer contains
nails. Never use the nailer as a toy.
Do not engage in horseplay. Always
keep others at a safe distance from
the work area in case of accidental
discharge of nails. Never point the
nailer at anyone. Accidental
triggering of the nailer could result
in death or serious personal injury.
Do not drive a nail on top of other
nails. The nail could glance and
cause death or a serious puncture
wound.
Do not operate or allow anyone else to
operate the nailer if any warnings or
warning labels are
not legible.
Warnings or
warning labels are
located on the
nailer magazine
and body.
Never leave the
nailer
unattended or
connected to an
air compressor
when not in
use. Serious
personal injury can occur if someone
picks up and uses the nailer without
knowing the correct way to operate
the nailer.
Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown,
examine the tool closely for bent,
cracked or broken parts and air
leaks. STOP and repair before using
or serious injury could occur.
Caution indicates a
potentially
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
Do not modify or alter the nailer or
any nailer parts. Do not use the nailer
if any shields or guards are removed
or altered. Do not use the nailer as a
hammer. Personal injury or tool
dam.occur.
Avoid long extended periods of work
with the nailer. Stop using the nailer
if you feel pain in hands or arms.
!
CAUTION
Always
check that
the Work
Contact
Element
(WCE) is
operating
properly. A
nail could
accidentally be driven if the WCE is
not working properly. Personal
injury may occur (See "Checking the
Work Contact Element" Section).
Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
fasteners can be ejected from the
front of the nailer. Personal injury
may occur.
Notice indicates
important
information, that if not followed, may
cause damage to equipment.
Avoid using the nailer when the
magazine is empty. Accelerated
wear on the nailer may occur.
Clean and check all air supply hoses
and fittings before connecting the
nailer to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
Air compressors providing air to the
nailer should follow the
requirements established by the
American National Standards
Institute Standard B19.3-1991;
Safety Standard for Compressors for
Process Industries. Contact your air
compressor manufacturer for
information.
NOTICE
Operating Instructions
!
WARNING
NS219000 NS289100 NS289500 NS349000
• REQUIRES
(SCFM with 16 nails 4.1 4.1 4.1 4.1
per minute @ 90 psi)
• AIR INLET 1/4” NPT 1/4” NPT 1/4” NPT 1/4” NPT
• NAIL LENGTH
RANGE 2” to 3
1
2 2” to 3
1
2 2” to 3
1
2 2” to 3
1
2
• NAIL SHANK 0.113” to 0.113” to 0.113” to 0.113” to
RANGE 0.131” 0.131” 0.131” 0.131”
• MAGAZINE
CAPACITY 60-75 75-105 75-105 75-105
• WEIGHT 8 lbs. 5 oz. 8 lbs. 15 oz. 7 lbs. 5 oz 8 lbs. 11 oz.
• LENGTH 19.5” 21.75” 21.75” 19.75”
• HEIGHT 15” 15” 15” 15”
• MAX PRESSURE 120 psi 120 psi 120 psi 120 psi
• PRESSURE RANGE 70 - 120 psi 70 - 120 psi 70 - 120 psi 70 - 120 psi
Nailer Components And Specifications
7-Sp
Modelos NS219000, NS289100, NS289500 y NS349000
Adjustable Direction
Exhaust Deflector
Threaded Hole/Tool
Balancer (M8 x 1.25)
Nail Loading
Area
Magazine
Single Cycle
Trigger
Warning Labels
Nail Discharge Area
Work Contact Element
www.chpower.com
Notas