Filter
Top Products
specifications
amplifier section PH 30.2
power output 4 (watts)
1
6 channel 6 x 75
3 channel 3 x 250
power output 2 (watts)
2
4 x 112.5
fuse type 70 A maxi
dimensions 13” x 19 7/8” x 2”
distortion all channels driven <0.1% 20Hz to 20,000Hz
frequency response ±1dB 10Hz to 30,000Hz
signal-to-noise ratio full >90dB
bandwidth @ rated output power
damping factor @ output >150
connector full bandwidth
input sensitivity 100mV to 8Vrms for full output
input impedance 47 k
crossover section3
ch 1 & 2 high-pass 12dB/octave variable 45Hz- 5kHz
ch 3 & 4 high-pass & low-pass 12 octave variable 45Hz- 5kHz
ch 5 & 6 low-pass 12 octave variable 45Hz- 5kHz
constant bass low-pass 12dB/octave 30Hz- 300Hz
1
All channels driven, continuous FTC rated 4
load, 20Hz to 20,000Hz, <0.1% THD, power input
voltage at 13.8DVC.
2
All channels driven, continuous FTC rated 2
load, 20Hz to 20,000Hz, <0.1% THD, power input
voltage at 13.8DVC.
3
All channels are selectable with infinitely variable adjustments from 45Hz to 5,000Hz with a slope
of 12dB/octave and a “Q” of .707.
about this manual
To get the most from your a/d/s/ PowerPlateTM, we recommend that you have the installation
performed by your qualified authorized a/d/s/ dealer. If this unit is installed by your dealer, we will
extend the warranty to three years instead of the standard one year. However, if you feel that you
have the necessary skills and prefer to perform the installation yourself, this manual will guide you
through the process of installation and set-up. Please read through it completely before beginning
the installation so that you may familiarize yourself with the total procedure before you begin. If
there is anything that you do not fully understand, please consult with your a/d/s/ dealer before
attempting the installation.
keep listening, but be safe!
Sustained listening to loud music over 100dB has been shown to cause permanent hearing damage.
Systems using a/d/s/ components are capable of achieving volume levels which substantially exceed
this level. When operating your system for sustained periods at high volume, be sure to use hearing
protection to prevent long-term exposure. We want you to be able to enjoy the music for many more
years.
features of your PowerPlate™
Remote Level Control Capability – Can be used with accessory control AC502 to provide a
dashboard mounted rear channel subwoofer or Constant Bass level control
Digital Crossover Frequency Display – The crossover frequency for each channel pair is displayed
on the top of the amplifier for quicker, more precise system tuning
Detachable Plug in Connector – High current speaker and power connector simplify installation.
Multi-cross™ Variable Built-in Crossover’s – High-pass, Low-pass and Bandpass functions are
built-in, virtually eliminating the need for external crossover networks in even the most elaborate
systems.
Constant Bass circuit – Signal from all input channels is summed, low-pass filtered and then made
available.
PowerPlate™ Design – a/d/s/ original low profile, high efficiency heatsink design keeps size to a
minimum and allows mounting where space is limited.
Wide Input Sensitivity Range – Allows connection to virtually any source unit from factory OEM
radios through low output preamps
Simultaneous Stereo and Mono – Each channel pair may be used Stereo, Mono, Bridged or both
Stereo and Mono simultaneously. This allows an additional Mono speaker to be used with a stereo
pair for center-channel or subwoofer applications from each channel pair using passive crossover’s.
Same Side Adjustments – The P-series PowerPlate™ makes system adjustment easy by organizing
all signal processing controls on one side of the amplifier. This layout allows convenient system
adjustment and facilitates a variety of installation possibilities when access to the controls is desired.
221