A SERVICE OF

logo

Open as PDF
next previous
English
2 ©WagnerSprayTech.Allrightsreserved.
English
Operating the High Pressure Spray Gun
Thegunisdesignedforpressuresupto3000PSI,207bar.
POSSIBLE INJECTION HAZARD - Do not spray without the tip
assembly in place. Never trigger the gun unless the tip is in
either the spray or the unclog position. Always lock the trigger
off when attaching the spray tip or when the spray gun is not in
use.
Locking the Spray Gun
Thegunissecuredwhenthetriggerlockisata90ºangle(perpendicular)tothe
trigger in either direction.
Attaching the Tip Assembly
1. Threadthesprayguardassemblyontothegun.Tightenbyhand.
Unclogging the Spray Tip
Do not attempt to unclog or clean the tip with your finger. Do
not use a needle or other sharp pointed instrument to clean the
tip. The hard tungsten carbide is brittle and can be chipped.
Thespraygunisequippedwithareversibletipwhichallowsyoutoblowout
anyparticlesofoldpaintorothercontaminantsthatmayobstructthepaint
owthroughthetip.Ifthespraypatternbecomesdistortedorstopscompletely
whilethegunistriggered,followthesesteps:
1. FollowPressureReliefProcedure(seesprayerinstructionmanual)
2. Rotatespraytip180degreesfromitscurrentposition.
3. Unlockthegunandsqueezethetrigger,pointingthegunatascrap
pieceofwoodorcardboard.Thisallowspressureinthesprayhoseto
blowouttheobstruction.Whenthenozzleisclear,paintwillcomeout
inastraight,highpressurestream.
4. Releasethetriggerandlocktheguno.
5. RotatespraytipforwardtooneoftheSPRAYpositions.
6. Unlockthegunandresumespraying.
Cleaning the Gun
IMPORTANT: If spraying with latex paint, use warm soapy water for
cleaning. If using oil or alkyd-based paints, use mineral spirits or paint
thinner. Refer to the paint manufacturer’s instructions for specic
recomendations.
Do not use mineral spirits or paint thinner on latex paint, or the mixture will
turn into a jellylike substance which is dicult to remove.
1. Checkthatthespraytipassemblyhasbeenremovedfromthegun.
2. Runtheappropriatesolventthroughthe
pump.
3. Holdthemetalpartofthegunagainstametal
container to ground the gun.
4. Triggerthegunintothecontaineruntilitis
ushedclean.Usethelowestpossiblepressure.
Cleaning the Filter
Thisltermustbecleanedeverytimeyouuseyoursprayer.Whenusingthicker
paints,theltermightneedtobecleanedmoreoften.
1. Unclipthetriggerguardfromthelterhousingbypullingoutwardfrom
thelterhousing.Unscrewthehousing.
Hole
Filter top
(tapered
end)
Trigger
guard
Filter
Filter housing
2. Removethelterfromthespraygunhousingandcleanwiththe
appropriatecleaningsolution(warm,soapywaterforlatexpaints,
mineralspiritsforoil-basedmaterials).
3. Inspectthelterforholes(seeHolepicture,above).Replaceifholesare
found.
IMPORTANT: Never poke the filter with a sharp instrument!
4. Replacethecleanedlter,taperedendrst,intothegunhousing.
5. Replacethehousingandspringandsnapthetriggerguardbackintothe
housing.