Filter
Top Products
System
Frequency Response (-3dB)
(1)
BM Back can
Frequency Range (-10dB)
(1)
BM Back can
Frequency Range (-10dB)
(1)
PI Back can
System Sensitivity (1W @ 1m)
(2)
Nominal Coverage Angle
Coverage Angle (1kHz to 6kHz)
Directivity Factor (Q)
Directivity Index (DI)
Rated Maximum SPL
Average
Peak
Average with THP60
Power Handling
(3)
Average
Programme
Peak
Recommended Amplifier Power
Nominal Impedance
Transformer Taps
(via front rotary switch)
70V
100V
Distortion
10% Full Power
250Hz
1kHz
10kHz
1% Full Power
250Hz
1kHz
10kHz
Crossover
Notes
(1) Average over stated Bandwidth. Measured in an IEC baffle in an Anechoic Chamber
(2) Unweighted Pink noise input, measured at 1m on axis
(3) Long term power handling capacity as defined in EIA - 426B test
A full range of measurements, performance data, CLF and Ease“’AA Data can be
downloaded from www.tannoy.com
Full independent verification of published specifications carried out by NWAA Labs,
California can also be obtained from the downloads section of www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction
of new materials or manufacturing methods will always equal or exceed the
published specifications, which Tannoy reserves the right to alter without prior
notice. Please verify the latest specifications when dealing with critical applications.
CMS801 DC
47Hz - 30kHz
40Hz - 35kHz
41Hz - 35kHz
92dB (1W = 2.83V for 8 Ohms)
90 degrees conical
100 degrees conical
5.5 averaged 1kHz to 6kHz
7.2 averaged 1kHz to 6kHz
112dB
118dB
110
90W
180W
360W
180W @ 8 Ohms
8 Ohms
60W / 30W / 15W / 7.5W / OFF
& Low Impedance operation
60W / 30W / 15W / OFF
& Low Impedance operation
2nd Harmonic 3rd Harmonic
0.65% 0.39%
1.36% 0.29%
1% 0.03%
2nd Harmonic 3rd Harmonic
0.20% 0.43%
0.49% 0.28%
0.42% 0.03%
2kHz - 2nd order LF, 2nd order HF
(with dynamic HF protection)
Transducers
Low Frequency
High Frequency
1 x 200mm (8.00") Dual Concentric
TM
constant directivity driver with multi fibre
paper pulp cone
1 x 25mm (1.00") titanium dome with
neodymium magnet system
Physical
Enclosure
Back can
Baffle
Grille
Safety Features
Clamping Design
Min / Max Clamping Range
Recommended Clamp Torque
Back Can Options
Blind Mount (BM)
Pre Install (PI)
Cable Entry Options
Conduit Knockouts
Connectors
Safety Agency Ratings
(pending)
BM Hole Cutout Diameter
PI Hole Cutout Diameter
Dimensions
Bezel diameter
Front of ceiling to
rear of back can (BM)
Front of ceiling to
top of safety loop (BM)
Front of ceiling surface to
rear of speaker unit (PI)
Front of accessory back can
bezel to top of safety loop (PI)
Net Weight (ea)
CMS801 DC BM
CMS801 DC PI
CMS801 Plaster (Mud) Ring
CMS801 PI 8ohm back can
CMS801 DC 60W
transformer kit 8 ohm
Included Accessories
Optional Accessories
Zinc plated steel
Reflex loaded UL 94V-0 rated ABS
Steel, with weather resistant coating
Safety ring located at rear of enclosure for
load bearing safety bond
Security toggle clamp
0.0mm (0.0") / 20.0mm (0.79")
1.5Nm
Complete with fixed back can
Separate backcan for Pre Installation
Cable clamp & squeeze connector for
conduit up to 22mm
3 Sets of horizontal positions 19/22/28mm
0.75/0.87/1.1"
Removable locking connector with screw
terminals with "loop through" facility
UL-1480, UL-2043, CE
295mm (11.61")
295mm (11.61")
325mm (12.80")
310.50mm (12.22")
327.80mm (12.90")
118.70mm (4.67 )
168.50mm (6.63")
CMS801 DC
TECHNICAL SPECIFICATIONS
CMS801 DC data file // issue 1.07// 15.07.08
Ordering Information
Part number
8001 4550
8001 4560
8001 4650
8001 4570
7600 1658
Model name
CMS801 DC BM
CMS801 DC PI
CMS801 Plaster (Mud) Ring
CMS801 PI 8ohm back can
CMS801 DC 60W transformer kit 8 ohm
Baffle / Grille Colour
White / paintable
White / paintable
Zinc plated steel
Zinc plated steel
N/A
Packed Quantity
2
2
10
1
1
Tannoy adopts a policy of continuous improvement and product specification is subject to change.
anfragen@tannoy.com
6.5kg (14.33lbs)
2.5kg (5.51lbs)
0.3685kg (0.81lbs)
4kg (8.81lbs)
1.095kg (2.41lbs)
C Ring, tile bridge,
paint mask,
cutout template, grille
Plaster (Mud) Ring