Filter
Top Products
Tannoy United Kingdom
Tannoy North America
Tannoy Deutschland
Tannoy France
T: 00 44 (0) 1236 420199
T: 00 1 (519) 745 1158
T: 00 49 (180) 1111 881
T: 00 33 (0)1 7036 7473
E: enquiries@tannoy.com
E: inquiries@tannoyna.com
E: anfragen@tannoy.com
E: ventes@tannoy.com
CMS501
Tannoyadoptsapolicyofcontinuousimprovementandproductspecificationissubjecttochange
CMS501datafile//issue1.06//10.01.08
TECHNICAL SPECIFICATIONS
F
requency Response (-3dB)
(
1)
8
5Hz - 22kHz
B
M Back can
Frequency Range (-10dB)
(1)
74Hz - 24kHz
B
M Back can
Frequency Range (-10dB)
(1)
74Hz - 24kHz
P
I Back can
System Sensitivity (1W @1m)
(2)
89dB (1W = 2.45V for 6 Ohms)
N
ominal Coverage Angle 90 degrees conical
Coverage Angle (1kHz to 6kHz) 105 degrees
Directivity Factor (Q) 5.6 averaged 1kHz to 6kHz
Directivity Index (DI) 7.0 averaged 1kHz to 6kHz
Rated Maximum SPL
(2)
Average 106dB
Peak 112dB
P
ower Handling
Average 50W
P
rogramme 100W
Peak 200W
Recommended Amplifier Power 100W @ 6 Ohms
Nominal Impedance 6 Ohms
Transformer Taps (via front rotary switch)
70V 30W /15W/ 7.5W/ 3.75W /OFF
& Low Impedance operation
100V 30W/ 15W /7.5W /OFF
& Low Impedance operation
Distortion
10% Full Power 2nd Harmonic 3rd Harmonic
250Hz 2.81% 0.14%
1kHz 0.5% 0.25%
10kHz 1.77% 0.04%
1% Full Power 2nd Harmonic 3rd Harmonic
250Hz 0.18% 0.09%
1kHz 0.16% 0.22%
10kHz 0.32% 0.09%
Crossover 7kHz inductively coupled
(1)Averageover statedbandwidth. Measuredat 1metre onaxis.
(2) Unweightedpinknoise input,measured at1 metre in ananechoic chamber
(3) Long termpower handlingcapacity asdefined inEIA-426B test
Afullrange ofmeasurements, performancedata, CLF and Ease™Data canbe
downloaded fromwww.tannoy.com
Full independent verificationof publishedspecifications carried out byNWAALabs,
California canalsobe obtainedfrom thedownloads section ofwww.tannoy.com
Tannoyoperates apolicy ofcontinuous research anddevelopment. Theintroduction
of new materialsor manufacturingmethods will always equalor exceedthe
published specifications, whichTannoyreserves theright toalter without prior
notice. Pleaseverifythe latestspecifications whendealing withcritical applications.
System CMS501
Transducers
8001 4450 CMS501 BM White / paintable 2
8001 4460 CMS501 PI White / paintable 2
8001 4180 CMS501 Plaster (Mud) Ring Zinc plated steel 10
8001 3830 CMS501 PI back can Zinc plated steel 1
PART NUMBER PACKED QUANTITYBAFFLE / GRILLE COLOURMODEL NAME
Ordering Information
Low Frequency 130mm(5.00")mineral loaded
polypropylene ICT™
High Frequency ICT™ aluminium dome
Physical
Enclosure
Back can Zincplated steel
Baffle Reflex loaded UL 94V-0 rated ABS
Grille Steel, with weather resistant coating
S
afety Features Safety ring located at rear of enclosure
f
or load bearing safety bond
Clamping Design Security toggle clamp
Min / Max Clamping Range 0.0mm (0.0") / 20.0mm (0.79")
Recommended Clamp Torque 1.5Nm
B
ack Can Options
B
lind Mount (BM) Complete with fixed back can
Pre Install (PI) Separate back can for pre installation
Cable Entry Options Cable clamp and squeeze connector for
conduit up to 22mm
Conduit Knockouts 3 Sets of horizontal positions
19 / 22 / 28mm (0.75" / 0.87" / 1.10")
Connectors Removable locking connector with screw
terminals with "loop through" facility
Safety Agency Ratings
(pending) UL-1480, UL-2043, CE
BM Hole Cutout Diameter 190mm (7.48")
PI Hole Cutout Diameter 190mm (7.48")
Dimensions
Bezel diameter 210mm (8.27")
Front of ceiling to
rear of back can (BM) 189.5mm (7.46")
Front of ceiling to
top of safety loop (BM) 206.8mm (8.14")
Front of ceiling surface to
rear of speaker unit (PI) 135.6mm (5.34")
Front of accessory back can
bezel to top of safety loop (PI) 153.50mm (6.04")
Net Weight (ea)
CMS501 BM 3.60kg (7.94lbs)
CMS501 PI 2.90kg (6.39lbs)
PI back can 2.60kg (5.73lbs)
Included Accessories C Ring, tile bridge, paint mask,
cutout template, grille
Optional Accessories Plaster (Mud) Ring