Sony M-100MC MP3 Player User Manual


  Open as PDF
of 3
 
Welcome!
Thank you for purchasing the Sony Microcassette-Corder.
Some features are:
•The three modes (Lecture, Meeting, or Dictation) allow you to
switch the microphone sensitivity and directionality so that the
microphone picks up the sound clearly depending on the
recording situation.
•The recorded sound is loud and clear with high power output.
•The BATT lamps indicate remaining battery power in two
steps and the i lamp indicates when to replace the batteries.
•The CUE MARKER function locates a specific position of a
dictation.
•The FAST PB (fast playback) function enables you to review
the contents approx. 20% faster than normal playback.
•The VOR (Voice Operated Recording) system starts and stops
recording automatically in response to the sound.
•Edit function—You can start recording directly from the
playback mode by pressing the r button to correct a
previously recorded portion.
•Tape counter
•Automatic shut-off mechanism at the end of the tape (in the
recording/playback mode only)
•Stop-pause-release function—The PAUSE switch is released
automatically when the p
button is depressed, so that you
don’t miss a recording chance.
Preparing Power Sources
Choose one of the following power sources.
Dry Batteries (see Fig. A-a)
Make sure that nothing is connected to the DC IN 3V jack.
1 Open the battery compartment lid.
2 Insert two R6 (size AA) batteries with correct polarity and
close the lid.
To take out the batteries (see Fig. A-b)
To attach the battery compartment lid, if it is
accidentally detached (see Fig. A-c)
Attach it as illustrated.
When to replace the batteries (see Fig. A-d)
Replace the batteries with new ones when the BATT indicators
go off and the i indicator flashes.
The BATT indicators change as illustrated:
Notes
• The unit will play back normally for a while, even after the i indicator
flashes. However, replace the batteries as soon as you can. If not, the
playback cannot be made with normal sound, noise may be recorded
and the recorded sound will not be loud enough.
• The i indicator flashes to indicate battery replacement during
playback, recording and pause (during pause by VOR function also).
• In the following cases you do not need to replace the batteries:
– if the BATT indicators flash with the playback sound when you turn
up the volume.
– if the i indicator lights momentarily when the tape starts running or
at the end of the tape.
– if the i indicator flashes during fast forward/CUE or rewind/
REVIEW.
Battery life* (Approx. hours)
Batteries Recording
Sony alkaline LR6 (SG) 16.0
Sony R6P (SR) 5.5
* Measured value by the standard of JEITA (Japan Electronics and
Information Technology Industries Association) (Using a Sony
Microcassette MC-60)
Note
The battery life may shorten depending on the operation of the unit.
House current (see Fig. A-e)
Connect the AC power adaptor to the DC IN 3V jack and to a
wall outlet. Use the AC-E30HG* AC power adaptor (not
supplied). (For World model: In Japan, use the AC-E30M, not
supplied.) Do not use any other AC power adaptor.
* For customers in Saudi Arabia:
AC-E30HG is not available in Saudi Arabia.
Note
Specification for AC-E30HG varies for each area. Check your local voltage
and the shape of plug before purchasing.
How to use the stands
You can position the unit to record the sound more clearly using
the stands. You can choose from the two types of stands
depending on the recording situation (see Fig. B-a).
To attach the stand if it is accidentally detached
(see Fig. B-b)
Attach it as illustrated.
Recording (see Fig. C-a)
1 Press the reset button of the TAPE COUNTER.
2 Press p and insert a standard microcassette with the side
to start recording facing the lid (see Fig. C-b).
3 Select the desired tape speed.
2.4cm for optimum sound (recommended for normal use):
A 30-minute recording can be made using both sides of the
MC-30 microcassette.
1.2cm for longer recording time: A 60-minute recording can
be made using both sides of the MC-30 microcassette.
4 Set MIC MODE to select the sensitivity of the
microphone (see “Using the MIC MODE selector”).
Lecture: to record the sounds from where the unit is aiming
(uni-directional). It is useful to record during a lecture.
Meeting: to record at meetings or in a quiet or spacious
place (omni-directional).
Dictation: to record for dictation or in a noisy place (omni-
directional).
5 Set VOR to ON or OFF.
If you set VOR to ON, the unit automatically starts
recording the sound and pauses when there is no sound
(you can save tapes and batteries).
When the sound is not loud enough, set it to OFF, or the unit
may not start recording.
6 Press r.
Recording starts. While the tape runs, the REC indicator
lights and flashes depending on the strength of the sound.
To Press or slide
Stop recording p
Start recording during r during playback (the unit becomes in
playback the recording mode)
The REC indicator lights.
Review the portion just Slide )CUE/0REVIEW toward
recorded 0REVIEW during the recording.
Release the button at the point to start
playback.
Pause recording Slide PPAUSE in the direction of the
arrow. The REC and BATT indicators go off.
To release pause recording, slideP PAUSE in
the opposite direction.
Take out a cassette p
Note
Select the 2.4 cm tape speed for recording, if you play back the recorded
tape with another unit. Otherwise, the sound quality may be changed.
Notes on VOR (Voice Operated Recording)
•The VOR system depends on the environmental conditions. If you
cannot get the desired results, set VOR to OFF.
•When you use VOR in a noisy place, the unit will stay in the recording
mode. If the sound is too soft, on the contrary, the unit will not start
recording.
Using the MIC MODE selector (see Fig. C-c)
Set MIC MODE to the desired position depending on the
recording situation.
To monitor the sound
Connect the earphone (supplied to World model only) to EAR
jack. The monitor volume cannot be adjusted by VOL.
To prevent a cassette from being accidentally recorded
over (see Fig. C-d)
Break out and remove the cassette tabs. To reuse the cassette for
recording, cover the tab hole with adhesive tape.
Recording cue marks
While recording, you can record a special signal on the tape to
mark a specific position.
At the desired position, push CUE MARKER to record a signal.
The REC indicator goes off for a while and a signal will be
recorded on the tape. If you want to record a signal longer than
that, push CUE MARKER as long as you want.
During cue and review, you will hear the beep sound at the
signal position. During playback, you will hear the signal with
low frequency.
Notes
•We recommend recording cue marks when there is a break in the sound.
•During cue and review, the beep sounds differently.
•The beep may sound differently depending on the marked position on
the tape because the winding speed varies from the beginning to the
end of the tape.
Playing a Tape (see Fig. D-a)
1 Insert a cassette with the side to start playing facing the lid
(see Fig. D-b).
2 Set TAPE SPEED to the same speed as that used for
recording.
3 Press (.
4 Adjust the volume.
To Press or slide
Stop playback/stop fast p
forward or rewind*
Pause playback Slide PPAUSE in the direction of the
arrow. The BATT indicator goes off.
To release pause playback, slide PPAUSE in
the opposite direction.
Fast forward Slide )CUE/0REVIEW toward
)CUE during stop.**
Rewind Slide )CUE/0REVIEW toward
0REVIEW during stop.**
Search forward during Keep )CUE/0REVIEW sliding toward
playback (CUE) )CUE during playback and release it at the
point you want.**
Search backward during Keep )CUE/0REVIEW sliding toward
playback (REVIEW) 0REVIEW during playback and release it at
the point you want.**
* If you leave the unit after the tape has been wound or rewound, the
batteries will be consumed rapidly. Be sure to depress p
.
** The tape moves faster in the rewind/REVIEW mode than in the fast
forward/CUE mode.
Note
If the tape is completely rewound while searching backward during
playback (REVIEW), )CUE/0REVIEW may not return to the center
position when you release it. In this case, push it back to the center
position to start playback.
To increase the playback speed
Slide the FAST PB switch in the direction of the arrow. The
playback speed will be increased.
To return to the original speed, slide the FAST PB switch to the
original position.
At the end of the tape
In the recording or playback mode, the tape stops at the end of
the tape and the locked buttons will be released automatically
(Automatic shut-off mechanism).
After fast forward or rewind, be sure to set )CUE/
0REVIEW back to the center position.
Dubbing onto another tape
recorder
(see Fig. E)
Connect another tape recorder using the RK-G64HG connecting
cord (not supplied). (In Japan, use the RK-G64, not supplied.)
Set this unit to the playback mode and another tape recorder to
the recording mode.
Precautions
On power
•Operate the unit only on 3 V DC.
For AC operation, use the AC adaptor recommended for the
unit. Do not use any other type. For battery operation, use two
R6 (size AA) batteries.
On the unit
•Use only the y (standard microcassettes) with
this unit. Non-standard cassettes cannot be used because their
“L” dimension (see illustration) is different (see Fig. F).
•Do not leave the unit in a location near heat sources, or in a
place subject to direct sunlight, excessive dust or mechanical
shock.
Polarity of the plug
English
•Should any solid object or liquid fall into the unit, remove the
batteries or disconnect the AC power adaptor, and have the
unit checked by qualified personnel before operating it any
further.
•Keep personal credit cards using magnetic coding or spring-
wound watches etc. away from the unit to prevent possible
damage from the magnet used for the speaker.
•When you do not use the unit for long, remove the batteries to
avoid damage caused by battery leakage and subsequent
corrosion.
•If the unit has not been used for long, set it in the playback
mode and warm it up for a few minutes before inserting a
cassette.
If you have any questions or problems concerning your unit,
please consult your nearest Sony dealer.
Troubleshooting
Should any problem persist after you have made these checks,
consult your nearest Sony dealer.
A cassette cannot be inserted.
n The cassette is being inserted in the wrong way. (The
cassette should be inserted in the lid with the tape side
facing upward.)
n ( has been already pressed.
r cannot be pressed.
n There is no cassette in the cassette compartment.
n The cassette tab has been removed.
r or ( cannot be pressed.
n The tape has reached the end.
n After the automatic shut-off, PPAUSE is slid in the
direction of the arrow.
The unit does not operate.
n The batteries have been inserted with incorrect polarity.
n The batteries are weak. Replace both batteries with new
ones.
n PPAUSE is slid in the direction of the arrow.
n The AC power adaptor or car battery cord is connected to
the unit only and you are going to use the unit on
batteries.
No sound comes from the speaker.
n The earphone is plugged in.
n The volume is turned down completely.
The sound drops out or comes with excessive noise.
n The volume is turned down completely.
n The batteries are weak. Replace both batteries with new
ones.
n The head is contaminated. See “Maintenance”.
During CUE/REVIEW, the tape stops or does not run. Or
you cannot fast-forward or rewind.
n The batteries are weak. Replace both batteries with new
ones.
Tape speed is too fast or too slow in the playback
mode.
n Improper setting of the TAPE SPEED switch. Set it to the
same speed as that used for recording.
Tape speed is faster than the normal playback speed.
n The FAST PB switch is slid in the direction of the arrow.
Recording cannot be made.
n The batteries are weak. Replace both batteries with new
ones.
n The head is contaminated.
n The VOR switch is set to ON. When you do not use VOR,
set it to OFF.
n Set the MIC MODE selector firmly at the correct position.
Recording is interrupted.
n The VOR switch is set to ON. When you do not use VOR,
set it to OFF.
Recording cannot be erased completely.
n The head is contaminated.
Maintenance (see Fig. G)
To clean the tape head and path
Press ( and wipe the head 1, capstan 2 and the pinch roller
3 with a cotton swab, moistened with alcohol every 10 hours of
use.
To clean the exterior
Use a soft cloth slightly moistened in water. Do not use alcohol,
benzine or thinner.
Specifications
Tape
y (normal position type)
Recording system
2-track 1-channel monaural
Speaker
Approx. 2.8 cm (1
1
⁄
8
in.) dia.
Tape speed
2.4 cm/s (
15
⁄
16
ips), 1.2 cm/s (
15
⁄
32
ips)
Frequency range
“Lecture”: 400 - 3,000 Hz
“Meeting”, “Dictation”: 400 - 4,000 Hz
Output
Earphone jack (minijack) for 8 – 300 ohms earphone
Power output (at 10% harmonic distortion)
220 mW
Battery life (recording)
See “Preparing Power Sources”.
Power requirements
3 V DC
Two R6 (size AA) batteries
Dimensions (w/h/d)
Approx. 126.0 × 68.0 × 40.8 mm (5 × 2
3
⁄
4
× 1
5
⁄
8
in.) incl. projecting
parts and controls
Mass
Approx. 180 g (6.4 oz) incl. batteries
Supplied accessories
Hand strap (attached to the unit) (1)
Microcassette tape (1) (Except for U.S.A., Canada and European
models)
Wind screen (1) (U.S.A., Canada and World model only)
R6 (size AA) batteries (2) (World model only)
Earphone (1) (World model only)
Design and specifications are subject to change without notice.
Optional accessories
Microcassette MC-60, MC-30
Earphone ME-81, ME-L82
Connecting cord RK-G64HG or RK-G64 (miniplug to miniplug with
attenuator)
AC power adaptor AC-E30HG or AC-E30M
Car battery cord DCC-E230
 previous