Sony CFD-S550 MP3 Player User Manual


  Open as PDF
of 2
 
Listening to the radio
1 Press RADIO BAND•AUTO PRESET until the band you want appears in the
display (direct power-on).
Each time you press the button, the indication changes as follows:
CFD-S550: “FM” t “AM”
CFD-S550L: “FM” t “MW” t “LW”
2 Hold down TUNE + or – until the frequency digits begin to change in the
display.
The player automatically scans the radio frequencies and stops when it finds a
clear station.
If you can't tune in a station, press the button repeatedly to change the frequency
step by step.
Tip
If the FM broadcast is noisy, press MODE until “Mono” appears in the display and the radio will play in
monaural.
Changing the AM/MW tuning interval
The AM/MW tuning interval is preset to 9 kHz at the factory.
If you need to change the AM/MW tuning interval, do the following:
1 While keeping the RADIO BAND•AUTO PRESET button and x button pressed,
disconnect the mains lead from the mains.
2 While keeping the RADIO BAND•AUTO PRESET button and x button pressed,
reconnect the mains lead to the mains. The tuning interval is changed and “AM 9”
“MW 9” or “AM 10” “MW 10” appears in the display for 2 seconds.
After changing the tuning interval, you need to reset your preset radio stations.
Presetting radio stations
You can store radio stations into the player’s memory. You can preset up to 30 radio stations
(CFD-S550), 20 for FM and 10 for AM in any order, or 40 radio stations (CFD-S550L), 20 for
FM and 10 for MW and LW in any order.
1 Press RADIO BAND•AUTO PRESET to select the band.
2 Hold down RADIO BAND•AUTO PRESET for 2 seconds until “AUTO” flashes
in the display.
3 Press DISPLAY•ENT•MEMORY.
The stations are stored in memory from the lower frequencies to the higher ones.
If a station cannot be preset automatically
You need to preset a station with a weak signal manually.
1 Press RADIO BAND•AUTO PRESET to select the band.
2 Tune in a station you want.
3 Hold down the number buttons that you want to preset the new station on for about 2 seconds.
To select the preset number over 10, press >10 first, then the corresponding number buttons.
You need to hold down the last number button to enter for about 2 seconds.
(Example: To select 12, press >10 and 1 first, then hold down 2 for about 2 seconds.)
Tip
The preset radio stations remain in memory even if you unplug the mains lead or remove the batteries.
Playing preset radio stations
1 Press RADIO BAND•AUTO PRESET to select the band.
2 Press the number buttons to tune in the stored station.
To tune in a preset station over 10, press >10 first, then corresponding number
buttons.
(Example: To tune in a preset station 12, press >10 and 1 first, and then press 2.)
Playing a tape
1 Press TAPE (direct power-on).
(On the remote, press OPERATE (or POWER) and then press FUNCTION
repeatedly until “TAPE” appears in the display.)
2 Press xZ to open the tape compartment and insert a recorded tape. Close the
compartment. Use TYPE I (normal) tape only.
3 Press n.
To
stop playback
fast-forward or rewind the tape
pause playback
eject the cassette
Recording
1 Press xZ to open the tape compartment and insert a blank tape. Use TYPE I
(normal) tape only.
2 Select the programme source you want to record.
To record from the CD player
Press CD and insert a CD (See “Playing a CD”).
To record from the radio
Press RADIO BAND•AUTO PRESET and tune in the station you want (See
“Listening to the radio”).
3 Press z to start recording.
(n is depressed automatically.)
To Press
stop recording xZ
pause recording X
Press the button again to resume recording.
Tips
• Adjusting the volume or the audio emphasis will not affect the recording level.
• If the AM or MW/LW programme makes a whistling sound after you've pressed z in step 3, press
MODE to select the position of ISS (Interference Suppress Switch) that most decreases the noise.
• For the best results, use the AC power as a power source for recording.
• To erase a recording, proceed as follows:
1 Insert a tape with the recording you want to erase.
2 Press TAPE.
3 Press z.
Press
xZ
m or M
X
Press the button again to resume play after pause.
xZ
To turn on/off the power
CFD-S550L: Press OPERATE.
CFD-S550: Press POWER.
To adjust the volume
Press VOL +, –.
To listen through headphones
Connect the headphones to the i (headphones) jack.
Adjusting the sound emphasis
To Select the sound characteristic
Press one of the SOUND MODE buttons to select the audio emphasis you want.
(On the remote, press SOUND repeatedly.)
Press To get
ROCK powerful, clean sounds, emphasizing low and high range audio
POP light, bright sounds emphasizing high and middle range audio
JAZZ percussive sounds, emphasizing bass audio
VOCAL the presence of vocals, stressing middle range audio
FLAT the whole dynamic range for music such as classical music
To reinforce the bass sound
Press MEGA BASS.
“MEGA BASS” appears in the display.
To return to normal sound, press the button again.
To get the MEGA Xpand effect
Press MEGA Xpand.
“MEGA Xpand” appears in the display.
You can get the effect of expansion of the sound field.
To return to normal sound, press the button again.
Falling asleep to music
1 Play the music source you want.
2 Press SLEEP to display “SLEEP.”
3 Press SLEEP to select the minutes until the player goes off automatically.
Each time you press the button, the indication changes as follows: “60” t “90” t “120”
t “OFF” t “10” t “20” t “30”
To cancel the sleep function
Press OPERATE (or POWER) to turn off the power.
Note
When you are playing a tape using this function:
If the tape length of one side is longer than the set time, the player will not go off until the tape reaches
the end.
Remote Control
Location of controls
FUNCTION
BAND
N
OPERATE
(POWER)
VOL +*,–
x
.,>
Playing a CD
1 Press CD (direct power-on).
(On the remote, press OPERATE (or POWER) and then press FUNCTION
repeatedly until “Cd” appears in the display.)
2 Load a CD in the CD compartment.
3 Press Z PUSH OPEN/CLOSE to close the CD compartment.
4 Press u (
NN
NN
N on the remote).
The player plays all the tracks once.
To
stop playback
pause playback
go to the next track
go back to the previous track
remove the CD
locate a specific track directly*
locate a point while listening
to the sound
locate a point while observing
the display
* You cannot locate a specific track if “SHUF” or “PGM” is lit in the display. Turn off the indication by
pressing x.
Tip
To locate a track numbered over 10, press >10 first, then the corresponding number buttons.
Example:To play track number 23, press >10 first, then 2 and 3.
Using the display
To check the total track number and playing time
Press DISPLAY•ENT•MEMORY in stop mode (see fig. E).
To check the remaining time
Press DISPLAY•ENT•MEMORY repeatedly while playing a CD. The display changes as
follows:
tthe current track number and playing time
r
the current track number and the remaining time on the current track*
r
the number of tracks left and remaining time on the CD
* For a track whose number is more than 20, the remaining time appears as “- -:- -” in the display.
Selecting the play mode
Press MODE until “REP 1” “REP ALL” “SHUF” “SHUF REP” “PGM” “PGM REP” appears in
the display. Then proceed as follows:
To Select
repeat a single track “REP 1”
repeat all tracks “REP ALL”
shuffle play “SHUF”
repeat tracks “SHUF REP”
in random order
programme play “PGM”
repeat programmed tracks “PGM REP”
To cancel selected play mode
Press MODE until the selected mode disappears from the display.
To check the programmed track and playing order in the display
To check the order of tracks before play, press DISPLAY•ENT•MEMORY.
Every time you press the button, the track number appears in the programmed order.
To change the current programme
Press x once if the CD is stopped and twice if the CD is playing. The current programme will be
erased. Then create a new programme following the programming procedure.
Tip
You can record your own programme. After you’ve created the programme, insert a blank tape and
press z to start recording.
Then do this
Press the number button for the track you want to
repeat.
Press u.
Press u.
Press u.
Press the number buttons for the tracks you want
to programme in the order you want up to 20
tracks (see fig. F). Then press u.
Press the number buttons for the tracks you want
to programme in the order you want up to 20
tracks. Then Press u.
Loading a CD
With the labeled side up
Inserting a cassette
With the side you want
to play facing you
Total track number Programmed track Playing order
EF
Total playing time
Display
Press
x
u (
XX
XX
X on the remote)
Press the button again to resume play after pause.
>
.
Z PUSH OPEN/CLOSE
a number button of the track
> (forward) or . (backward) while playing until you
find the point
> (forward) or . (backward) in pause until you find
the point
CD
MEGA BASS
Z PUSH
OPEN/CLOSE
VOL –, +*
., >
TUNE –, +
DISPLAY
ENT MEMORY
MODE
x
u*
OPERATE
(POWER)
SLEEP
OPR/BATT
RADIO BAND
AUTO PRESET
TAPE
Display
Remote sensor
SOUND MODE
SLEEP
Number buttons
MODE
TUNE –, +
X
MEGA Xpand
MEGA Xpand
MEGA BASS
SOUND
*The button has a tactile dot.
Number buttons
*
OPTICAL DIGITAL OUT (CD)
(CFD-S550L only)
LINE (CFD-S550L only)
i
LINE IN (CFD-S550L only)
Connecting optional components
(CFD-S550L only)
You can record a CD on a MiniDisc and enjoy the sound from other components, such as
portable MD, CD player and TV, VCR through the speakers of this player.
Be sure to turn off the power of each component before making connections. For details, refer to
the instructions of the component to be connected.
Recording a CD on a MiniDisc recorder or DAT recorder
1 Connect the OPTICAL DIGITAL OUT (CD) jack of this player with the digital
input jack of MiniDisc and DAT using the digital connecting cable* (not
supplied).
* Select a connecting cable depending on the type of the digital input jack of the recorder to be
connected. For details, refer to the instruction manual of the component to be connected. The
OPTICAL DIGITAL OUT (CD) jack of this player is square-shaped jack.
The type of the jack Model number of
of the component the connecting cable
to be connected
Optical miniplug POC-5AB
(MiniDisc recorder, etc.)
L-type 7-pin connector POC-DA12P
(DAT recorder, etc.)
Square-shaped optical POC-10A
connector (MiniDisc
recorder, DAT recorder, etc.)
2 Turn on the power of this player and the connected component.
3 Make the connected component ready for recording.
4 Press u to start playing a CD.
Listening to the sound from the connected component
1 Connect the LINE IN jack of this player with the line output jack or headphones
jack of other component using the audio connecting cable* (not supplied).
*For MiniDisc recorder: a cable with a stereo-mini plug on both ends.
*For TV, VCR: a cable with a stereo-mini plug on one end and two phono plugs
on the other end.
2 Press LINE to display “LInE”.
3 Play the optional component connected to the LINE IN jack of the player.
Tip
You can record the sound from the connected component. Insert a blank tape into the tape compartment,
and press z.
Notes
• Connect the cords firmly to avoid any malfunction.
• When other components are not connected, close the cover for the OPTICAL DIGITAL OUT (CD)
and LINE IN jacks to keep out dust.
 previous