Sony ICF-CD533L Clock Radio User Manual


 
Owner’s Record
The model number and the serial number are
located on the top.
Record the serial number in the space provided
below. Refer to these numbers whenever you call
upon your Sony dealer regarding this product.
Model No.
Serial No.
WARNING
To prevent fire or shock
hazard, do not expose
the unit to rain or
moisture.
This symbol is intended to alert the user
to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock to persons.
This symbol is intended to alert the user
to the presence of important operating
and maintenance (servicing) instruc-
tions in the literature accompanying the
appliance.
The graphical symbols are on the top
enclosure.
For Customers in the U.S.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
INFORMATION
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the
equipment and receiver.
—Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/
TV technician for help.
CAUTION
The use of optical instruments with this
product will increase eye hazard.
For Customers in Europe
This Compact Disc player is
classified as a CLASS 1
LASER product.
The CLASS 1 LASER
PRODUCT label is located on
the bottom exterior.
For Customers in Canada
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
H
L
Various Ways of
Playback
You can play tracks repeatedly or in random
order.
1 Press PLAY MODE during play.
Each press changes the play mode as
follows:
none (normal play) ?
All the tracks are played once.
.
“REP 1” (single repeat)
A single track is played repeatedly.
.
“REP” (all repeat)
All the tracks are played repeatedly.
.
“SHUFFLE REP” (shuffle repeat)
All the tracks are played repeatedly
in random order.
.
“SHUFFLE” (shuffle play)
All the tracks are played once
in random order.
Operating the Radio
Manual Tuning
1 Press RADIO to turn on the radio.
2 Select FM, AM(MW) or LW (ICF-
CD533L only) by pressing BAND.
Each press of BAND changes the band.
3 Tune in a station by pressing TIMER
ADJ/TUNE + or .
The FM channel step is set to 0.1 MHz and
the AM channel step is set to 10 kHz for the
model for North and South America. The FM
channel step is set to 0.05 MHz and the
AM(MW) channel step is set to 9 kHz for the
model for other countries. (The FM frequency
indication changes every 0.1 MHz.)
The LW channel step is set to 9 kHz. Beeps
sound at the band edge. After 5 seconds, the
indication becomes the current time but the
“RADIO” indication remains.
4 Adjust volume using VOL.
To turn off the radio, press RADIO/CD OFF.
To improve radio reception
FM: Extend the AC power cord fully to
improve FM reception.
AM(MW)/LW: When installing the unit, rotate
the unit horizontally for optimum
reception and then install the unit.
A ferrite bar antenna is built into the
unit.
To check the station you are listening to,
press RADIO lightly. The band and frequency
will appear for about 5 seconds.
Preset Tuning
You can preset up to five FM/AM(MW)/LW
stations in random.
Example: To set AM 1260 kHz in memory
presets button 1.
1 Tune in the AM 1260 kHz (See “Manual
Tuning”).
2 Hold down the desired preset button
until the beeps sound.
The frequency will appear for about
5 seconds and then return to the current time.
To change the preset station, preset a new
station in the number of which you want to
change the station. The previous station is
canceled.
Tuning in a Preset Station
1 Press RADIO.
2 Press a preset number button of the
station you want to tune in.
3 Adjust volume using VOL.
Setting the Count
Down Timer
Use the timer as a reminder. The beep sounds for
60 minutes when the preset time has passed.
The beep sounds when the radio is on or off.
The timer can be set at 1 minute intervals
between 0:01–24:00.
1 Press TIMER•SET/ON/OFF.
TIMER” will appear in the display.
2 While “TIMER” is in the display, press
TIMER ADJ/TUNE + or .
When the desired time appears in the
display, release TIMER ADJ/TUNE + or
and press TIMER•SET/ON/OFF. The
beep sounds twice, and the timer is set.
When the time has elapsed, the buzzer
will sound and the display flashes.
While the timer is set, the display shows the
remaining time. To display the current time,
press CLOCK.
To stop the beep in the middle of beeping,
press TIMER•SET/ON/OFF.
To cancel the timer setting time, before the
time elapses, hold down TIMER•SET/ON/OFF
until “TIMER” disappears.
The timer setting time is canceled and the
current time appears in the display.
Preset Timer
You can preset up to five different count down
timers.
1 Set the timer (See “Setting the Count
Down Timer”).
2 Hold down the desired preset button
until the beeps sound.
Operating the Preset
Timer
1 Press TIMER•SET/ON/OFF.
2 Press the desired preset button.
3 Press TIMER•SET/ON/OFF again.
TIMER
Before You Begin
Thank you for choosing the Sony CD clock radio!
The CD clock radio will give you many hours of
reliable service and listening pleasure.
Before operating the CD clock radio, please read
these instructions thoroughly and retain them for
future reference.
These instructions cover these models:
ICF-CD533 and ICF-CD533L.
Their differences are shown below.
Model Number ICF-CD533 ICF-CD533L
Band FM/AM FM/MW/LW
Features
Built-in CD Player with Shuffle/Repeat
function.
24 hour Count Down Timer with 5 timer
presets.
A powerful bass is produced with the MEGA
BASS sound system.
3 Speaker System.
PLL (Phase Locked Loop) Synthesized Tuner
with 5 random memory presets which is a
easy one button station setting.
Installing the Unit
Under a Cabinet (See
Fig. A)
The unit can be installed without the spacer.
1 Mark the position of the 4 holes by
using the supplied template. Use a drill
to make the holes (size 6.5 mm dia.,
1
/
4
inch). (See Fig. A-a)
2 When the cabinet door overhangs the
shelf and obstructs the unit, you can
adjust the unit/shelf height.
First set the L mark to the dot which
becomes the lowest position, then you
can adjust the height in 4 steps (H••L)
by turning the spacer counterclockwise.
(See Fig. A-b)
3 Install the unit with the supplied
mounting screws. (See Fig. A-c)
Caution
Since the unit is very heavy, be careful when
installing the unit.
To reduce the risk of fire, do not place any
heating or cooking appliance beneath this
unit.
Install the unit so that its AC power cord can
be connected directly to a wall outlet. Do not
use a converter or extension cord.
Be sure that the AC power cord has no slack
when using the unit, since the cord acts as an
FM wire antenna. If the AC power cord has
some slack, wind it up to the cord hook until
the cord has no slack.
The unit has a built-in ferrite bar antenna for
AM radio reception. Check the condition of
AM reception before fixing in position.
Install the unit as far as possible from a source
of noise. (for example, refrigerator, microwave
oven, fluorescent lamp, etc.)
Setting the Clock
1 Plug in the unit.
The display will flash “AM 12:00” or “0:00”.
2 While holding down CLOCK, press
TIME ADJ + or until the correct time
appears in the display.
When you release CLOCK, the clock begins to
operate and “:” flashes.
The clock system varies depending on the
model you own.
12-hour system: “AM 12:00” = midnight, “PM
12:00” = noon.
24-hour system: “0:00” = midnight, “12:00” =
noon.
To set the current time rapidly, keep pressing
the + or button while holding down CLOCK.
To set the current time from zero seconds, at
step 2, release CLOCK with the time signal.
Playing a Disc
An 8 cm (3-inch) CD can be played without an
adaptor.
1 Press 6 OPEN/CLOSE and place a CD
on the disc tray.
2 Press CD ^.
The disc tray closes and the player plays all
the tracks once.
3 Adjust volume using VOL.
To Press
Pause CD ^
Resume play after CD ^ again
pause
Locate the beginning =**
of the current
track (AMS*)
Locate the next +**
track (AMS)
Go back at high speed Hold down =**
Go ahead at high Hold down +**
speed
Locate the previous = repeatedly**
track (AMS)
Locate the succeeding + repeatedly**
track (AMS)
Stop play RADIO/CD OFF
*AMS = Automatic Music Sensor
**These operations are possible during both play
and pause.
•To handle compact discs
This way
Handle the disc
by its edge.
Not this way
Do not touch the
surface.
Do not stick paper or
tape nor write
anything on the
surface.
Note
When you press CD ^, if there is no disc in
the CD compartment, the “00” indication
flashes for about 5 seconds and the unit will
be turned off.
Useful Functions
To Obtain Powerful Bass
Turn MEGA BASS to adjust the bass volume.
The “MEGA BASS” system produces a powerful
bass sound.
Precautions
Operate the unit on the power sources
specified in “Specifications.”
The nameplate indicating voltage, etc. is
located at the top.
Disconnect the mains lead by grasping the
plug. Never pull it by the cord.
Do not leave the unit in a location near a heat
source such as a radiator or airduct, or in a
place subject to direct sunlight, excessive dust,
mechanical vibration, or shock.
Allow adequate air circulation to prevent
internal heat build-up. Do not place the unit
on a surface (a rug, a blanket, etc.) or near
materials (a curtain) which might block the
ventilation holes.
Should any liquid or solid object fall into the
unit, unplug (or remove batteries from) the
unit and have it checked by a qualified
personnel before operating it further.
When the casing becomes soiled, clean it with
a soft cloth dampened with a mild detergent
solution. Never use abrasive cleansers or
chemical solvents, as they may mar the casing.
The unit is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the unit
itself has been turned off.
For detailed safety precautions, see the
“IMPORTANT SAFEGUARDS” leaflet.
(for U.S.A. only)
If you have any question, please consult your
nearest Sony dealer.
Troubleshooting
Should any problem occur with the unit, make
the following checks to determine whether or not
servicing is required. If the problem persists,
consult the nearest Sony dealer.
The CD player does not operate.
Did you close the CD tray?
Did you place a disc correctly?
The disc should be placed with the labelled
surface up.
Dusty or defective disc—Clean the disc with
an optional cleaning cloth. Wipe the disc from
the center out.
Take out the CD and leave the CD tray open
for about an hour to dry moisture
condensation.
Skipping of sound in CD operation
Dusty or defective disc—Clean or replace the
disc.
Reduce the volume.
Strong vibration
Specifications
CD player section
System: Compact disc digital audio system
Laser diode properties: Material: GaAlAs
Wavelength: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a
distance of about 200 mm from the objective
lens surface on the optical pick-up block with
7mm aperture.)
Frequency response: 20-20,000 Hz
+1
–1.5
dB
Wow and flutter: Below measurable limit
Radio section
Frequency range:
Model for North America
FM: 87.5-108 MHz
AM: 530-1,710 kHz
Model for other countries
FM: 87.5-108 MHz
AM(MW): 531-1,602 kHz
LW: 153-279 kHz (ICF-CD533L only)
Channel step:
Model for North and South America
FM: 0.1 MHz (fixed)
AM: 10 kHz (fixed)
Model for other countries
FM: 0.05* MHz (fixed)
AM(MW); 9 kHz (fixed)
LW: 9 kHz (fixed) (ICF-CD533L only)
* The frequency display is raised or lowered
by steps of 0.1 MHz.
(Example: Frequency 88.05 MHz is
displayed as "88.0 MHz".)
General
Time display:
Model for North America and UK: 12-hour
system
Model for other countries: 24-hour system
Speaker:
Front Speakers: 6.6 cm (2
5
/
8
inches) × 2, 8
ohms
Woofer: 9.2 cm (3
5
/
8
inches) 4 ohms
Power outputs:
Front Speakers: 1.5W + 1.5W
(at 10% harmonic distortion)
Woofer: 4.5 W (at 10% harmonic distortion)
Power requirements:
North American model: 120 V AC, 60 Hz
Other models: 220-230 V AC, 50 Hz
Power consumption:
Model for U.S.A.: 20W
Model for other countries: 22W
Dimensions: Approx. 355.5 × 112.5 × 308 mm
(w/h/d)
(Approx. 14 × 4
1
/
2
× 12
1
/
4
inches) incl.
projecting parts and controls
Mass: Approx. 3.4 kg (7lb 8oz) not incl. parts
Supplied accessory: Mounting screws (4),
Template (1), Spacers (4), Cord clamp (1)
Design and specifications are subject to change
without notice.
3-859-469-22 (1)
Sony Corporation 1997 Printed in Malaysia
FM/AM Kitchen CD
Clock Radio
ICF-CD533
FM/MW/LW Kitchen CD
Clock Radio
ICF-CD533L
Operating Instructions
Mode d'emploi
English
A
b
c
TIMER
AC power cord
Cord clamp
Mounting screw
a
Cord hooks
Template
Spacer
Dot
L(Low)
CD
RADIO
12345
OFF
PLAY
MODE
BAND
CLOCK
SET/ON/OFF
PRESET TIMER / TUNING
SELECT/ PRESET
=+
TIMER TIMER ADJ/TUNE
TIME ADJ
+--
^
6
OPEN/
CLOSE
MAX
VOL
MEGA BASS
MIN
MIN MAX
FM RADIO CD TIMER
SHUFFLE
REP 1ALL
TRACK
MW
AM
LW
PM
AM
TIMER