Filter
Top Products
Installing the Unit
Under a Cabinet
(See Fig. A)
The unit can be installed without the spacer.
1
Mark the position of the 4 holes by using
the supplied template. Use a drill to
make the holes (size 6.5 mm dia.,
9
/
32
inch). (See Fig. A-a)
2 When the cabinet door overhangs the
shelf and obstructs the unit, you can
adjust the unit/shelf height.
First set the L mark to the dot which
becomes the lowest position, then you
can adjust the height in 4 steps (H••L)
by turning the spacer counterclockwise.
(See Fig. A-b)
3 Install the unit with the supplied
mounting screws. (See Fig. A-c)
Caution
• Since the unit is very heavy, be careful when
installing the unit.
•
To reduce the risk of fire, do not place any
heating or cooking appliance beneath this unit.
• Install the unit so that its AC power cord can
be connected directly to a wall outlet. Do not
use a converter or extension cord.
• Be sure that the AC power cord has no slack
when using the unit, since the cord acts as an
FM wire antenna. If the AC power cord has
some slack, wind it up to the cord hook until
the cord has no slack.
• The unit has a built-in ferrite bar antenna for
AM radio reception. Check the condition of
AM reception before fixing in position.
• Install the unit as far as possible from a source
of noise. (for example, refrigerator, microwave
oven, fluorescent lamp, etc.)
Setting the Clock
1 Plug in the clock radio.
The display will flash “AM 12:00”.
2 Press CLOCK for a few seconds.
You will hear a beep and the hour will start
to flash in the display.
3 Press TUNE/TRACK/TIME SET + or –
until the correct hour appears in the
display.
4 Press CLOCK once.
The minute will flash.
5 Repeat steps 3 and 4 to set the minute.
After setting the minute, press CLOCK to start
the counting of the seconds, and you will
hear two short beeps.
•To set the current time rapidly, hold down
TUNE/TRACK/TIME SET + or –.
•The clock system varies depending on the
model you own.
12-hour system: “AM 12:00” = midnight
•In step 5, when you press CLOCK after the
minute setting to activate the clock, the seconds
start counting from zero.
To change the display to the
daylight saving time (summer time)
indication
Press D.S.T./SUMMER T..
“
” is displayed and the time indication
changes to summer time.
To deactivate the summer time function, press
D.S.T./SUMMER T. again.
Changing
AM Channel Step
The AM channel step differs depending on
areas. The channel step of this unit is factory-set
to 9 kHz or 10 kHz to match the frequency
allocation system of the country as listed.
You can change the channel step.
Area Channel step
AM FM
North and South
American countries
10 kHz 0.1 MHz
Other countries 9 kHz 0.05 MHz
1 Press OFF to turn off the power.
2 While holding down OFF, keep
pressing PRESET 1 for more than 5
second. Two short beeps will sound,
and the AM channel step will be
changed.
If you proceed step 2 again, the
channel step changes again.
• When the AM channel step is changed, the
preset stations will be erased.
• When the AM channel step is changed, the FM
channel step is also changed.
Playing a CD
An 8 cm (3-inch) CD can be played without an
adaptor.
1 Press Z OPEN/CLOSE and place a CD
on the disc tray.
2 Press Z OPEN/CLOSE to close the disc
tray.
3 Press CD ^.
The player plays all the tracks once.
4 Adjust volume using VOLUME.
To Press
Pause CD u
Resume play after CD u again
pause
Locate the beginning .**
of the current
track (AMS*)
Locate the next >**
track (AMS)
Go back at high speed Hold down .**
Go forward at high Hold down +**
speed
Locate the previous . repeatedly**
track (AMS)
Locate the succeeding > repeatedly**
track (AMS)
Stop play x
* AMS = Automatic Music Sensor
**These operations are possible during both play
and pause.
•To handle compact discs
Correct
Handle the disc
by its edge.
Incorrect
Do not touch the
surface.
Do not stick paper or
tape nor write
anything on the
surface.
Note
If you press CD u when there is no disc in the
CD compartment, “00” flashes for about 5
seconds on the display and the unit turns off
automatically.
Various Modes of CD
Playback
You can play tracks repeatedly or in random
order.
Press CD PLAY MODE.
Each press changes the play mode as
follows:
Display Play
indication mode
none (normal play)
All the tracks are played once.
m
“REP 1” (single repeat)
A single track is played repeatedly.
m
“REP ALL” (all repeat)
All the tracks are played repeatedly.
m
“SHUFFLE” (shuffle play)
All the tracks are played once
in random order.
m
“SHUFFLE REP” (shuffle repeat)
All the tracks are played repeatedly
in random order.
Playing the Radio
Manual Tuning
1 Press RADIO ON•BAND to turn on the
radio.
“RADIO” appears in the display.
The display shows the band and frequency
for a few seconds and then changes back to
the current time.
2 Press RADIO ON•BAND repeatedly to
select the desired band.
Each press changes the band as follows:
* When using FM1 or FM2 preset mode, you
may listen to the radio on either mode
(See “Preset Tuning”).
3 Use TUNE/TRACK/TIME SET + or – to
tune in to the desired station.
The FM channel step is set to 0.1 MHz and
the AM channel step is set to 10 kHz.
Two short beeps sound when the
minimum frequency of each band is
received during tuning.
4 Adjust volume using VOLUME.
•To turn off the radio, press OFF.
•To improve radio reception
FM: Extend the AC power cord fully to
improve FM reception.
AM: When installing the unit, rotate the unit
horizontally for optimum reception and
then install the unit. A ferrite bar antenna
is built into the unit.
•To check the station being received, press
RADIO ON
• BAND lightly. The display shows
the band and frequency for a few seconds and
then changes back to the current time.
Preset Tuning
You can preset 10 stations in FM (5 stations in
FM1, 5 stations in FM2) and 5 stations in AM.
Presetting a Station
Example: To preset FM90 MHz onto preset
button 2 for FM2.
1 Press RADIO ON•BAND to turn on the
radio.
2 Press RADIO ON•BAND to select FM2.
3 Tune in to the station on FM90 MHz
(See “Manual Tuning”).
4
Hold down the PRESET TUNING
button 2 until you hear two short beeps.
The display shows the frequency for a few
seconds and then changes back to the current
time.
To change a preset station
Tune in manually to the station you want to store
and hold down the PRESET TUNING buttons(1-5)
until you hear two short beeps. The previously
stored station will be replaced by the new one.
AC power cord
Cord clamp
Template
Spacer
L (Low)
Dot
Mounting screw
H
L
V
O
L
U
M
E
A
b
a
c
Tuning in to a preset station
1
Press
RADIO ON•BAND
to turn on the
radio.
2
Press
RADIO ON•BAND
to select the
band.
3
Press the PRESET TUNING button
lightly where the desired station is stored.
4 Adjust the volume using VOLUME.
After a few seconds, the display returns to
the current time but the preset button
number remains.
Note
When the PRESET TUNING buttons(1-5) are
pressed lightly, the radio station that is preset
will be selected. When they are pressed for a
while, the station that is on will be newly preset.
Useful Functions
To Obtain Powerful Bass
Switch MEGA BASS to ON.
The “MEGA BASS” system produces a powerful
bass sound.
Setting the Alarm
Before setting the alarm, make sure to set the
clock (see “Setting the Clock”).
To Set the Alarm Time
1 Turn off the radio.
2 Press ALARM for a few seconds.
You will hear a beep and the hour will start
to flash in the display.
3 Press TUNE/TRACK/TIME SET + or –
until the desired time appears in the
display.
4 Press ALARM once.
The minutes starts to flash.
5 Repeat steps 3 and 4 to set the minute.
Two short beeps will confirm the
setting, and the display will show the
current time.
When TUNE/TRACK/TIME SET + or – is held
down, the displayed time initially changes in
one-minute steps, and after about a second,
switches to ten-minute steps.
To Check the Alarm
Time
Press ALARM.
The display shows the alarm time for a few
seconds and then returns to show the current
time.
ALARM ON —
To Set the Alarm Mode
Press ALARM ON/OFF to set the alarm.
“ ” will appear in the display.
When the alarm comes on at the preset time,
“
” flashes in the display.
ALARM OFF —
The alarm is turned off automatically after
59 minutes.
To Stop the Alarm
Press OFF•ALARM RESET to turn off the
alarm.
The alarm will come on again at the same time
the next day.
To Cancel the Alarm
Press ALARM ON/OFF.
“ ” will disappear from the display.
<