Filter
Top Products
6.35
x 0.8 F
AST O
N
T
erm
inal
4 x Ø 5.3 Holes on Ø 172
Ø 162.5 max.
Ø 117.5 max.
Ø 145.3 max.
68.5 max.
8
+
Red dot
Ø 187.5 max.
(on angles)
1060 1070
TYPICAL CHARACTERISTICS
Rated impedance Z 8 16 Ω
Reference efficiency (1 W@1 m) - 97 97 dB SPL
Usable frequency range
1
- 300–6000 300–6000 Hz
Power handling capacity
2
(AES) - 130 130 W
Max Sound Pressure Level
3
SPLmax 114 114 dB SPL
Min. impedance modulus Zmin 6.0 @ 640Hz 12.9 @ 640Hz Ω
Voice-coil inductance
4
@ 1 kHz L
e1k
0.58 1.22 mH
@ 10 kHz L
e10k
0.23 0.48 mH
Bl product Bl 8.5 11.2 N/A
Moving mass M
ms
0.0085 0.0085 Kg
THIELE-SMALL PARAMETERS : TYPICAL (QC LIMITS)
Resonance frequency
5
F
s
130 (±25) 130 (±25) Hz
DC resistance
6
R
e
5.4 (±0.5) 11.6 (±1.1) Ω
Mechanical quality factor Q
ms
6.6 6.6 1
Electrical quality factor Q
es
0.52 0.50 1
Total quality factor Q
ts
0.48 0.46 1
Mechanical suspension compliance C
ms
180 180 10
-6
m/N
Effective piston area S
d
0.0150 0.0150 m
2
Equivalent C
as
air load V
as
0.0056 0.0056 m
3
Max. linear excursion X
max
±2.0 ±2.0 mm
Linear displacement volume V
d
0.030 0.030 10
-3
m
3
Half-space efficiency 2.3 2.3 %
Unity load volume V
as
Q
ts
2
1.3 1.2 10
-3
m
3
ABSOLUTE MAXIMUM RATINGS
Short term max. input voltage
7
V
max
65 90 V
Max. excursion before damage X
dam
4.0 4.0 mm
Ambient operating temperature –10 to +50 °C
Storage temperature
8
–20 to +70 °C
Environmental conditions
9
Outdoor
APPLICATION INFORMATION
Air volume occupied by the driver
10
0.46 0.46 10
-3
m
3
Speaker net mass 2.15 2.15 Kg
Recommended reflex box V
b
/F
b
3L / sealed L / Hz
Electrical polarity A positive voltage applied on the red
terminal produces forward cone motion.
SPECIFICATION NOTES
Note 1 : Allowing for energy response, excursion
capability, Power spectrum, and -3dB low
freq. roll-off for standard reflex tuning.
Note 2 : Established at 20°C ambient temp, according to
AES2-1984 standard using IEC268-1 simulated
programme signal and a 3 liter sealed test enclosure
with a 2nd order high-pass filter @ 400Hz.
Note 3 : Established at 1m on axis of the loudspeaker mounted
in test enclosure, when driven at full AES Power
Handling Capacity, including 4dB of thermal
compression loss.
Note 4 : Measured at 20 mA in free air.
Note 5 : Measured at 20 mA and 20°C ambient temp.
in free air conditions, after full run and rest.
Note 6 : Measured at 20°C ambient temp.
QC limits are ±10 %
Note 7 : Stated in RMS voltage according to IEC 268-5.
Note 8 : Includes shipping conditions. The lower limit prevents
from demagnetization.
Note 9: Our products are classified in three categories :
Indoor, Outdoor, and Outdoor
✚
for permanent
outdoor use or severe conditions.
Note 10 : Calculated for front mounting on to a 18 mm thick
board.
PHYSICAL CHARACTERISTICS
PHL Audio S.A. provides these specifications as representative of current production after conditioning. Because of our continuous research, they are subject to change without notice.
461, rue des chênes ■ Z.A
77590 CHARTRETTES
FRANCE
Tél : 33 01 64 81 29 80
Fax : 33 01 60 69 10 28
e-mail : phlaudio@phlaudio.com
http: //www.phlaudio.com
1060
■
1070
6.5” Midrange Extended Drivers