Filter
Top Products
- 4 -
POWER
SET
+–
MENU
EARPHONE
VOLUME
SELECT
CHANNEL
POWER
SET
+–
MENU
EARPHONE
VOLUME
SELECT
CHANNEL
HOW TO SET UP AND USE YOUR TV
Press the POWER but-
ton to turn ON the TV.
Press the VOLUME ▲
or ▼ button to adjust the
sound level. Also, press the
VOLUME ▲ button to select
an item in the menu.
Press the CHANNEL ▲
or ▼ button to select TV
channels. When channels are
not programmed, the TV will
search until a channel is found.
You also may press the
CHANNEL ▲ or ▼ button to
adjust items in the menu.
T
ELEVISION
The tuned
channel number
will appear briefly
when you turn on the
TV and when you
change channels. To
display the channel
number, press the
DISPLAY button. To
remove the channel
number, press the
DISPLAY button
again. The channel
number will not
remain on screen if a
Closed Captioning
mode is selected.
SMART
HELP
MENU
Press the MENU but-
ton repeatedly to select
CHANNEL SET with the
TV’s on screen arrow.
Press the SELECT but-
ton repeatedly or the SET
+/- buttons to select TV or
CATV. The selected mode
will appear in PURPLE.
• Select TV if you have an
antenna connected to the TV.
• Select CATV if you have a
Cable signal connected to
the TV.
Press the MENU button
to select AUTO MEMO
with the TV’s on screen
arrow. AUTO MEMO will
appear in PURPLE.
Press the SELECT but-
ton to start automatic chan-
nel programming.
VOL
CH
CH
PO
W
E
R
SLEEP
DISPLAY
ALT.CH
SELECT
M
EN
U
S
E
T
VOL
o
p
1
23
4
56
7
89
0
+100
o
p
+
–
M
U
TE
REMOTE
T
o load the batteries into
the remote:
1.
Slide off the battery com-
partment lid on the
remote control.
2.
Insert two AA batteries
(supplied) into the bat-
tery compartment as indi-
cated by the + / - markings
inside the battery compart-
ment. Batteries installed
incorrectly may damage
the remote control.
3.
Replace the lid.
Point the remote control
toward the remote sensor on
the TV when operating the
TV with the remote.
Press the MENU button
to display the TV’s on screen
menu. Press the MENU button
repeatedly to select an item in
the menu. Also, press the
MENU button repeatedly to
remove the menu.
SMART
H
ELP
When AUTO
MEMO action is
completed, the low-
est memorized chan-
nel reappears on the
screen.
Cancel AUTO
MEMO by pressing
the MENU button.
Battery
Compartment
Lid
Battery
Compartment
F
ollow these steps to quick-
ly add area channel num-
bers into the TV’s memory.
CHANNEL AUTO MEMO
Connect earphones (not supplied) to the EAR-
PHONE jack on the front of the cabinet if you
want to enjoy private personal listening.
Note: Do not connect earphones that have an L-
shaped plug. This type plug may interfere with
the cabinet and may not connect properly.
MENU Button
Press to access the on screen
menu. Press repeatedly to
move through the menu or to
remove the menu.
V
OL(ume) ▲/▼ Buttons
Press to adjust the TV
sound level.
Number
Buttons
Press two number buttons to
select TV channels. For exam-
ple, to select channel 6, press
0,6.
When you select cable chan-
nels which are equal or greater
than the number 100, press the
+100 button, then press the last
two digits of the channel you
want. For example, to select
channel 117, press the +100
button, 1,7.
MUTE
Button
Press to eliminate the sound
on the TV. Press again to
restore the sound.
CH(annel)
oo
/
pp
Buttons
Press to scan through pro-
grammed channel numbers.
If the TV is not receiving a
signal or if channels are not
programmed, the TV will
search until a channel is found
or until you press the MENU
button. In this case, check
antenna connections and pro-
gram the channels.
SELECT
Button
Press to select items in the
menu.
SLEEP
Button
Press to set the TV to
turn itself OFF automat-
ically.
POWER
Button
Press to turn the TV ON and
OFF.
ALT. CH (Alternate Channel)
Button
Press to return to the TV chan-
nel you were viewing immedi-
ately before switching to your
current channel.
SET
+/- Buttons
Press to select items in the
menu or to adjust the picture
controls.
DISPLA
Y
Button
Press to display the channel
number at all times. (If a
Closed Captioning mode is
selected, the channel num-
ber will appear only
briefly.) To remove the
channel number, press the
DISPLAY button again.