Filter
Top Products
4 Play
Play from iPod/iPhone
You can enjoy audio from iPod/iPhone through this unit.
Compatible iPod/iPhone
Apple iPod and iPhone models with a 30-pin dock connector:
iPod classic, iPod touch, iPod nano, iPod 5th generation (video), iPod
•
with color display, iPod mini.
iPhone, iPhone 3G, iPhone 3GS.
•
Listen to the iPod/iPhone
1 Place the iPod/iPhone into the dock.
2 Press SOURCE repeatedly to select iPod/iPhone source.
The connected iPod/iPhone plays automatically.
»
To pause/resume play, press
•
.
To skip to a track, press
•
/ .
To search during play, press and hold
•
/ , then release to
resume normal play.
Charge the iPod/iPhone
When the unit is connected to power, the docked iPod/iPhone begins
to charge.
Tip
For certain iPod models, it may take up to a minute before the •
charging indication appears.
Play from an external device
You can also listen to an external audio device through this unit.
1 Press SOURCE repeatedly to select AUX source.
2 Connect the supplied MP3 link cable to:
the
• MP3 LINK jack (3.5mm) on the back of the unit.
the headphone jack on an external device.
•
3 Start to play the device (see the device user manual).
5 Listen to radio
Note
Only FM radio reception is available on this unit.•
Tune to a radio station
Tip
Position the antenna as far as possible from TV, VCR or other radia-•
tion source.
Note
For optimal reception, fully extend and adjust the position of the •
antenna.
1 Press SOURCE to select FM.
2 Press and hold TUNING +/- for more than 2 seconds.
[SRCH]
»
(search) displays.
The radio tunes to a station with strong reception
»
automatically.
3 Repeat step 2 to tune to more stations.
To tune to a weak station, press
•
TUNING +/- repeatedly until
you fi nd optimal reception.
Program radio stations automatically
You can program a maximum of 20 preset radio stations.
1 In the tuner mode, press and hold DATE • AUTO TUNE/TIME SET
for more than 2 seconds to activate automatic program mode.
[AUTO] (auto) idisplays.
»
All available stations are programmed in the order of
»
waveband reception strength.
The fi rst programmed radio station is broadcast automatically.
»
Program radio stations manually
You can program a maximum of 20 preset radio stations.
1 Tune to a radio station.
2 Press DATE • AUTO TUNE/TIME SET to activate the program
mode.
PR01 begins to blink.
»
3 Press DATE • AUTO TUNE/TIME SET to confi rm.
4 Repeat the above steps to program other stations.
Tip
To overwrite a programmed station, store another station in its •
place.
Select a preset radio station
1 Press / to select a preset program number.
6 Other features
Set the alarm timer
You can set two alarms which go off at different time.
1 Ensure that you have set the clock correctly.
2 Press and hold AL 1 or AL 2 for 2 seconds.
[AL 1] or [AL 2] begin to blink.
»
3 Press SOURCE repeatedly to select an alarm sound source: iPod/
iPhone, iPod/iPhone playlist, FM tuner, or buzzer.
4 Press AL 1 or AL 2.
Hour digits begin to blink.
»
5 Press TUNING +/- or
/ repeatedly to set the hour.
6 Press AL 1 or AL 2 to confi rm.
Minute digits begin to blink.
»
7 Repeat steps 5-6 to set the minute.
8 Repeat steps 5-6 to select whether to ring alarm the whole week,
on weekdays, or at weekend.
9 Repeat steps 5-6 to set the alarm volume.
Tip
If you want to wake up to specifi c music track(s) on iPhone/iPod, •
after set iPhone/iPod playlist as the wake up source on the unit, you
need to create a playlist called ‘PHILIPS’ via iTunes and copy the
track(s) to this new ‘PHILIPS’ playlist.
If no playlist is created or there is no song in the playlist, the unit will
•
play the music track according to the last music playback preference
on iPhone/iPod.
Activate and deactivate the alarm timer
1 Press AL 1 or AL 2 repeatedly to activate or deactivate the timer.
If the timer is activated, [
»
AL 1] or [ AL2] is displayed.
If the timer is deactivated,
»
before [AL1] or [AL2] disappears.
Gentle wake
Gentle wake function peacefully wakes you with gently ascending alarm
volume.
If selected the alarm source iPhone/iPod, iPhone/iPod playlist or FM,
•
alarm volume will gentle increase.
If selected the alarm source Buzzer, the alarm will increases beep
•
tone frequency within seconds.
Repeat alarm
1 When the alarm rings, press BRIGHTNESS/REP ALM.
The alarm repeats ringing minutes later.
»
Tip
You can press • / to adjust the interval to repeat alarm.
Stop alarm ring
1 When the alarm rings, press the corresponding AL 1 or AL 2.
The alarm stops but the alarm settings remain.
»
View the alarm settings
1 Press AL 1 or AL 2.
Backup Battery Mode
Under normal use, the unit should be powered through the AC adapter.
If the AC adapter is disconnected, the unit will automatically switch to
Backup Battery mode.
Under Backup Battery mode:
The unit displays the same as under the Standby mode, with
•
backlight off.
Only the functions below are available:
•
Clock
•
Alarm
•
Note
Alarm source is defaulted to ‘Buzzer’ under Backup Battery mode.•
When AC Power is plugged back, the unit will exit Backup Battery
mode and go to Standby mode.
Note
• Under Backup Battery mode, the unit can work over 3 months.
When the battery power is low, the display panel will indicate
•
“bAtt Lo” until the batteries are empty and the unit will switch off
automatically. In this case, please replace the batteries in the backup
battery compartment with 2 pieces of new 1.5V, AAA/R03/UM4
batteries.
Install backup batteries
Caution
Risk of explosion! Keep batteries away from heat, sunshine or fi re. •
Never discard batteries in fi re.
Risk of product damage! When the apparatus is not used for long
•
periods, remove the battery.
1 Open the battery compartment on the back of the unit.
2 Insert 2 x 1.5V R03/UM-4/AAA batteries with correct polarity.
3 Close the battery compartment.
Note
• Batteries contain chemical substances, so they should be disposed
of properly.
Set the sleep timer
This unit can switch to standby automatically after a set period of time.
1 Press SLEEP repeatedly to select a set period of time (in minutes).
The sleep timer is activated
»
The display shows
»
The volume starts to decrease gradually from the last 5
»
minutes of sleep timer
The unit switches to standby when reaches the set time.
»
To deactivate sleep timer
1 Press SLEEP repeatedly until [OFF] displays.
»
disappears on the display.
Adjust display brightness
1 Press BRIGHTNESS/REP ALM repeatedly to select different levels
of display brightness.
7 Adjust sound
Adjust volume level
1 During play, press VOL +/- to increase/decrease the volume level.
Enhance bass
1 During play, press DBB to turn on or off dynamic bass enhance-
ment.
If DBB is activated, [DBB] is displayed.
»
8 Product information
Note
Product information is subject to change without prior notice.•
Specifi cations
Amplifi er
Rated Output Power 2 x 2.5 W RMS
Frequency Response 125 Hz - 16 kHz, ±3 dB
Signal to Noise Ratio >55 dB
MP3 link 500 mV RMS 10 kohm
Tuner
FM
Tuning Range 87.5 - 108 MHz
Tuning grid 50 KHz
Sensitivity
- Mono, 26dB S/N Ratio
- Stereo, 46dB S/N Ratio
<22 dBu
<45 dBu
Search Selectivity <36 dBu
Total Harmonic Distortion <3%
Signal to Noise Ratio >45 dB
General information
AC power (power adaptor) AS190-090-Al180;
Input: 100-240 V~, 50/60Hz, 0,7 A;
Class II;
Output: 9.0V
1.8A
Operation Power Consumption 10 W
Standby Power Consumption <1 W
Dimensions
- Main Unit (W x H x D) 216.9 x105 x139.4 mm
Weight
- Main Unit 0.75 kg
9 Troubleshooting
Warning
Never remove the casing of this apparatus. •
To keep the warranty valid, never try to repair the system yourself.
If you encounter problems when using this apparatus, check the follow-
ing points before requesting service. If the problem remains unsolved, go
to the Philips web site (www.philips.com/welcome). When you contact
Philips, ensure that the apparatus is nearby and the model number and
serial number are available.
No power
Ensure that the AC power plug of the unit is connected properly.•
Ensure that there is power at the AC outlet.•
No sound
Adjust the volume.•
No response from the unit
Disconnect and reconnect the AC power plug, then turn on the •
unit again.
Poor radio reception
Increase the distance between the unit and your TV or VCR.•
Fully extend the FM antenna.•
Timer does not work
Set the clock correctly.•
Switch on the timer.•
Clock/timer setting erased
Power has been interrupted or the power plug has been discon-•
nected.
Reset the clock/timer.•
Note