Filter
Top Products
GENERAL INFORMATION / CD PLAY
Only use the AY 3545 (4822 219 10033) or AY 3548 (3140 118 71890) car voltage
converter (4.5 V DC, positive pole to the centre pin) and the AY 3501 car adapter
cassette. Any other product may damage the set.
1 Put the set on a horizontal, vibration-free and
stable surface. Make sure it is in a safe place,
where the set is neither a danger nor an
obstacle to the driver and the passengers.
2 Plug the voltage converter into the
cigarette lighter socket (only for 12 V car
battery, negative grounding), then connect
the wired end with 4.5V DC input socket on the
set.
3 If necessary, clean the cigarette lighter socket
to obtain a good electrical contact.
4 Turn down the volume and connect the cassette adapter plug to LINE OUT/p
on the set.
5 Carefully insert the cassette adapter into the car radio’s cassette compartment.
6 Make sure the cord does not hinder your driving.
7 Decease the volume on the set, if necessary. Start playback on the set and
adjust the sound with the car radio controls.
• Always remove the voltage converter from the cigarette lighter socket
when the set is not in use.
Note: If your car radio has a LINE IN socket , it is better to use it for the
car radio connection instead of the cassette adapter. Connect the signal
lead to this LINE IN socket and to LINE OUT/p on the set.
4,5 V DC
12 V DC
O
P
E
N
V
O
L
E
O
F
F
•
R
S
U
M
E
•
H
O
L
D
O
U
T
L
I
N
E
/
4
4
9
In-car use (connections supplied or optionally available)
CD PLAY / FEATURES
• If a CD-Recordable (CD-R) or a CD-Rewritable (CD-RW) is not recorded
properly, nF dISC is displayed, indicating that the CD has not been
finalized. In that case, use FINALIZE on your CD recorder to complete the
recording.
• When playing a CD-Rewritable (CD-RW), please note that it takes 3–15
seconds after pressing 2; for sound reproduction to start.
• Playback will stop if you open the CD lid.
• While the CD is read, 01 --:-- flashes in the display.
Volume and bass
Volume adjustment
• Adjust the volume by using VOL E.
Bass adjustment
•Press DBB to switch the bass enhancement on or
off
yDBB appears if the bass enhancement is
activated.
DBB
Playback information
This CD-player can play all kinds of Audio Discs such
as CD-Recordables and CD-Rewritables. Do not try to
play a CD-ROM, CDi, VCD, DVD or computer CD.
1 Push the OPEN
2
slider to open the player.
2 Insert an audio CD, printed side up, by pressing the
CD onto the hub.
3 Close the player by pressing the lid down.
4 Press 2; to switch the player on and start playback.
yThe current track number and elapsed playing
time are displayed.
•You can pause playback by pressing 2;.
yThe time at which playback was paused starts
flashing.
•You can continue playback by pressing 2; again.
5 Press 9 to stop playback.
yThe total number of tracks and the total playing
time of the CD are displayed.
6 Press 9 again to switch the player off.
•To remove the CD, hold it by its edge and press the
hub gently while lifting the CD.
Note: If there is no activity, the set will automatically
switch off after a while to save energy.
3
O
P
E
N
V
O
L
O
U
T
L
I
N
E
/
4
4
9
E
/
4
4
9
ESP
ESP
0
Playing a CD
Selecting a track during playback
• Briefly press ∞ or § once or several times to skip to the current, previous or
next track.
yPlayback continues with the selected track, and
the track’s number is displayed.
Selecting a track when playback is stopped
1 Briefly press ∞ or § once or several times to select
the desired track. The track number is displayed.
2 Press 2; to start CD play.
yPlayback starts with the selected track.
Searching for a passage during playback
1 Keep ∞ or § pressed to find a particular passage in
a backward or forward direction.
ySearching starts while playback continues at low
volume. After 2 seconds the search speeds up.
2 Release the button when you reach the desired passage.
yPlayback continues from this position.
Notes: – If the player is in SCAN mode (see MODE chapter), searching is not
possible.
– In shuffle, shuffle repeat all or repeat mode (see MODE chapter), or
while playing a program, searching is only possible within the
particular track.
4
4
9
Selecting a track and searching