Philips AX 2102/01 Portable CD Player User Manual


 
Programming track numbers
You can store up to 30 tracks to play in a program.
A single track may be stored more than once in the
program.
1 While playback is stopped, select a track with
or §.
2 Press PROGRAM to store the track.
y
program
lights up; the track number
programmed and Pwith the total number of
stored tracks are displayed.
3 Select and store all desired tracks in this way.
4 Press 2; to start playback of your selected tracks.
y
program
is shown and playback starts.
You can review the program by pressing PROGRAM
for more than 2 seconds.
yThe display shows all the stored tracks in sequence.
Notes: – If you press
PROGRAM
and there is no track selected,
SEL
is
displayed.
– If you try to store more than 30 tracks,
FULL
is displayed.
Clearing the program
While playback is stopped, press 9 to clear program.
yCLris displayed once,
program
goes off,
and the program is cleared.
Note: The program will also be cleared if the power supply is interrupted, or if
the CD-player lid is opened, or if the set switches off automatically.
RESUME and HOLD
You can interrupt playback and continue (even after an
extended period of time) from the position where
playback stopped (RESUME) and you can lock all buttons
of the set so that no action will be executed (HOLD).
Use the RESUME–HOLD–OFF slider for these functions.
RESUME – continuing from where you have stopped
1 Switch the slider to RESUME during playback to activate RESUME.
y
resume
is shown.
2 Press 9 whenever you want to stop playback.
3 Press 2; whenever you want to resume playback.
y
resume
is shown and playback continues
from where you have stopped.
To deactivate RESUME, switch the slider to OFF.
y
resume
goes off.
HOLD – locking all buttons
You can lock the buttons of the set by switching the slider to HOLD. Now, when a
key is pressed, no action will be executed. This is of use, for example, when
transporting the player in a bag. With HOLD activated, you can avoid accidental
activation of other functions.
1 Switch the slider to HOLD to activate HOLD.
yAll buttons are locked. HoLdis shown when
you press any button. If the set is switched off,
hold
will be shown only when 2; is pressed.
2 To deactivate HoLd, switch the slider to OFF.
Note: If you deactivate
HoLd
by switching the slider to
RESUME,
you will be acti-
vating the
RESUME
function.
FEATURES FEATURES
It is possible to play tracks in random order, to repeat a single track or the entire
CD, and to play the first few seconds of each track.
1 Press MODE during playback as often as required in
order to activate one of the following ‘modes’. The
active mode is shown in the display.
y
shuffle
: All tracks of the CD are played in
random order until all of them have been played
once.
y
shuffle repeat all
: All tracks of the CD
are played repeatedly in random order.
y
repeat
: The current track is played repeatedly.
y
repeat all
: The entire CD is played repeatedly.
ySCAN: The first 10 seconds of each of the
remaining tracks are played in sequence.
2 Playback starts in the chosen mode after 2 seconds.
To return to normal playback, press MODE repeatedly until the display shows
no active modes.
ESP / Power Save Mode
With a conventional portable CD-player you might have experienced that the
music stopped e.g. when you were jogging. The Electronic Skip Protection
prevents loss of sound caused by light vibrations and shocks. Continuous playback
is ensured. However ESP does not prevent playback interruptions during vigorous
running. It also does not protect the unit against any damage caused by dropping!
In this set ESP is default ON. It is possible to set ESP off. and enter the Power
Save Mode.(PS). PS helps to extend battery lifetime for longer playback.
Press MODE for more than 2 seconds.
y disappears.
Press MODE again for more than 2 seconds.
yPSis displayed once
ESP on
ESP off
Power Save
ESP on
resume
resume
hold
A
A
A
Selecting a track during playback
Briefly press or § once or several times to skip to
the current, previous or next track.
yPlayback continues with the selected track, and
the track’s number is displayed.
Selecting a track when playback is stopped
1 Briefly press or § once or several times to select
the desired track. The track number is displayed.
2 Press 2; to start CDplay.
yPlayback starts with the selected track.
Searching for a passage during playback
1 Keep or § pressed to find a particular passage in
a backward or forward direction.
ySearching starts while playback continues at low
volume. After 2 seconds the search speeds up.
2 Release the button when you reach the desired passage.
yPlayback continues from this position.
Notes: – If the player is in SCAN mode (see MODE chapter), searching is not
possible.
– In shuffle, shuffle repeat all or repeat mode (see MODE chapter), or
while playing a program, searching is only possible within the
particular track.
P
R
OG
RA
M
M
O
D
E
D
B
B
T
R
A
C
K
M
O
D
E
shufflerepeatall
program
program
program
P
R
O
G
R
A
M
M
O
D
E
D
B
B
T
R
A
C
K
M
O
D
E
P
R
O
G
R
AM
M
OD
E
D
B
B
T
R
A
C
K
M
O
D
E
A
Selecting a track and searching
Selecting different playing possibilitiesMODE