Filter
Top Products
Repeat function
Press during play or stop mode.
The setting is switched in the sequence indicated below each
time [`] is pressed.
1-track repeat (1 `)(-------------------------------------]
One track is repeated. |
v|
All-track repeat (ALL `) |
All the tracks on the disc are repeated |
v|
Cancel (no indicator is shown) ======}
For your reference:
If [`] is pressed during program play, only the tracks in the
program are repeated.
(The indication “ALL” is not displayed.)
Changing the sound quality
Press during play or stop mode.
The setting switches in the sequence indicated below each time
[S-XBS] is pressed.
S-XBS>Cancel (no indicator is shown)
^========b
S-XBS:
Select this setting to boost the low-range response.
Anti shock works by reading audio data and storing it in
memory. The unit then fills in interruptions caused by
bumps and vibrations with data from the memory up to
10 seconds worth.
This unit also incorporates a powerful anti-shock mech-
anism that prevents skipping caused when play speed
is changed by swinging of the unit.
Press during play or stop mode.
The following indicator appears on the display.
Note!
If you have pressed [A.SHOCK] when the unit is in stop
mode, press [1;] to start play.
When bumps continue repeatedly
The following indicator appears on the display and
sound is interrupted.
∫ To program the same track in the sequence more than
once
∫ After step 3, press [MEMORY/RECALL] desired number of
times.
∫ If “'” is displayed
∫ No more tracks can be programmed.
∫ To confirm the contents of the program
∫ Press [MEMORY/RECALL] while the disc is playing. (The
number of the programmed tracks appear on the display in se-
quence.)
∫ To delete the entire programmed sequence
∫ Press [∫, OPR OFF].
Program play
Up to 24 tracks can be entered in the programmed sequence.
Preparation: Put unit in stop mode.
1
2
Select the desired track.
3
Register in sequence.
(The indication “M” and the programmed sequence appear
on the display.)
4
Repeat steps 2 and 3 to program all the
desired tracks.
5
Other Play Methods
The letters such as A in the various illustrations refer to the descriptions in the “Location of Controls” section (see page 2).
4
N
O
RM
AL
RAND
O
M
L
RESU
M
E
L
R
ESU
M
E
RAND
O
M
N
O
R
M
AL
RESUM
E
L
RAN
DO
M
NO
RM
AL
:
9
6
5
A
F
MEMORY/
RECALL
1
;
D
`
E
J
S-XBS
B
S-XBS
RQT6165
Note!
≥The anti-shock setting can be changed during play,
but this may cause a slight interruption in the sound
because the disc’s rotation speed changes.
≥During anti-shock operation, the disc rotates at a high-
er rate than usual to collect extra audio data. This
could result in a slight increase in disc rotation noise.
Listening to sound with the unit con-
nected to an audio system
The anti-shock function uses digital signal compression
technology. It is recommended that the anti-shock func-
tion be canceled if the unit is connected to a home
audio system.
Anti-Shock Function (Anti-Skip System)
I
A.SHOCK
B
A.SHOCK
B
Maintaining the
Lens
Open the lid and clean the lens as shown in the figure.
Use a cotton swab to gently wipe off any finger-prints.
Recommended product: Lens cleaner kit (SZZP1038C)
Air blower for
camera lens
Lens
DATE OF PURCHASE
DEALER NAME
DEALER ADDRESS
TELEPHONE NUMBER
User memo:
Resume play
This function allows you to listen from the beginning of the track
where play stopped because the unit was powered off (or
switched to stop mode). It is useful when listening to CDs in the
car, etc.
For your reference:
≥If [RESUME, RANDOM, NORMAL] is put in the
[RESUME] position, the all-track repeat function will be activat-
ed automatically as soon as the unit is powered on.
≥If power is cut off near the end of a track (off mode), playback
may resume from the beginning of the next track.
≥If the unit is powered off while a disc was playing and then a
new disc is inserted, play will begin from the middle of the new
disc because the unit remembers the position where play
stopped on the previous disc.
Release
To cancel the anti-shock function
Press [A.SHOCK] again.
Skip play
The disc plays from the specific track through to the end, then
play stops automatically.
Preparation: Put unit in stop mode.
1
2
Select the desired track.
3
Random play
1
2
For your reference:
≥It is also possible to press [9] while the unit is in stop mode
to change the first track to be played. (All tracks are played
eventually, regardless of which is played first.)
≥Program play is not possible in the random mode.
Release
RESUM
E
L
R
AN
DO
M
NO
R
M
AL
:
9
6
5
A
1
;
D
R
ESU
M
E
L
NO
R
M
AL
R
AN
D
O
M
1
;
D
L
R
ESU
M
E
R
ANDO
M
NO
RM
AL
Lens