Filter
Top Products
RQT5685
3
1
Switch [ ] to “TUNER”.
(Power comes on.)
2
Press [BAND] to select “FM” or “AM”.
3
(Omit this step if using the remote control)
If “ ” is on the display, press
[TUNE MODE] to clear it off .
4
Press [–/g] or [f/+] to
tune to the desired station.
The frequency changes one step
each time a button is pressed.
Automatic tuning
Keep [–/
g] or [f/+] depressed and release when the frequency
display starts to change. A station with good reception is automati-
cally selected and the process stops.
To stop automatic tuning, press [–/
g] or [f/+] again.
Note
Automatic tuning may stop on a frequency where there is no station if
there is interference. Press [–/
g] and [f/+] to tune if this occurs.
5
Adjust the volume.
To use auto scan
You can search for a station by listening to all tuned-in stations for 8
seconds each.
Preparation: Switch [ ] to “TUNER”.
1. Press [BAND] to select “FM” or “AM”.
2. Press [AUTO SCAN].
Auto scan starts.
3. Press [AUTO SCAN] when you find the desired station.
Auto scan ends when it reaches the original frequency again.
To stop during the process, press [AUTO SCAN].
To improve reception
FM: Extend the whip antenna and adjust its direction.
AM: Adjust facing of the unit.
If noise is excessive in the FM stereo mode
Press [FM MODE]. (“
” lights up.)
Sound will be produced in monaural, but this also reduces noise.
Press the button again to cancel. (“
” goes out.)
To receive FM broadcasts allocated in 0.1
MHz
(Only from the main unit)
First press [BAND] to select “AM”. Now, press and hold [BAND]. The dis-
play changes in a few seconds to show the current lowest FM frequency.
Continue to hold down the button.
The minimum frequency changes and the step is changed at the same
time. Changing the step erases all preset stations.
Repeat the above to change the step back.
Preset the stations (twelve FM and twelve AM) to make tuning simpler.
1
Tune to the desired station.
Do steps 1–4 on the left.
2
Press [MEMORY].
3
While “ ” and the frequency are
flashing
Press [MEMORY].
4
While “ ” and the preset channel
are flashing
Press [–/g] or [f/+] to
select the desired channel.
(Remote control: [
44
44
4] or [
33
33
3])
5
Press [MEMORY].
(This completes presetting.)
6
Repeat steps 1–5 to preset other stations.
Note
If “
” goes off during presetting, return to step 2.
Press [BAND] to select “FM” or “AM”.
(Omit this step if using the remote control)
Press [TUNE MODE] to display
“
”.
Press [–/
g] or [f/+] to select
the desired channel (1–12).
(Remote control: [
44
44
4] or [
33
33
3])
To use preset scan
You can search for a station by listening to all preset channels for 8
seconds each.
1. Do steps to above.
For remote control, replace [–/
g] or [f/+] described below with [
44
44
4]
or [
33
33
3].
2. Press and hold [–/
g] or [f/+] until “PS” appears on the display.
3. Press [–/
g] or [f/+] when you find the desired channel.
Preset scan ends after searching through each preset channel once.
To stop during the process, press [–/
g] or [f/+].
Normal tuning Preset tuning
Listening to radio broadcasts
To listen to preset channels
How to preset
Indicates
auto scan
Indicates
preset scan
“ ” lights when an FM stereo
broadcast is being received.
Preset channel
Preset channel
3
2
15 4
1
2
3
235 4
p3-4 3/25/05, 4:10 AM3