Filter
Top Products
Step 29. Enable Alarm 1 Submenu
If flashing
ENBL
is displayed, press
a
, if
DSBL
is displayed,
press
b
until
ENBL
is displayed, then press
d
to store and
go to the next menu item.
Step 30. Select the Deviation Control Type Submenu
Press
d
. If flashing
_DEV
Deviation is displayed press
a
,
otherwise press
b
until flashing
_DEV
is shown. Now
press
d
to store and go to next menu item.
Step 31. Select the Latched Type Submenu
Press
d
. If flashing
UNLT
Unlatched is displayed press
a
,
otherwise press
b
until
UNLT
is displayed.
Press
d
to store and advance to next menu item.
Step 32. Select the Normally Open Type of Contact
Closure Submenu
Press
d
. If flashing
N.o.
Normally Open is displayed,
press
a
, otherwise press
b
until
N.o.
is displayed. Press
d
to store and advance to next menu item.
Step 33. Select the Above Type of Active Submenu
Press
d
. If flashing
ABoV
Above is displayed, press
a
,
otherwise press
b
until
ABoV
is displayed. Press
d
to store
and advance to next menu item.
Step 34. Enable Alarm 1 at Power On (
A.P.oN
)
Press
d
. If flashing
ENBL
is displayed, press
a
, otherwise
press
b
until
ENBL
is displayed. Press
d
to store and
advance to next menu item.
Step 35. Enter Alarm 1 High Submenu
Press
a
twice to skip
ALR.L
Alarm 1 Low value.
ALR.L
is
for below &
ALR.H
for above.
Step 36. Set the Alarm 1 High value
(
ALR.H
)
Press
d
. Press
b
or
c
until value to set the display to
002.0
. Press
d
to save.
Step 37. Enter the Alarm 2 Menu
The display will show
ALR2
the top menu for Alarm 2.
Repeat steps from 28 to 36 to set for Alarm 2 the same
conditions as for Alarm 1.
Step 38. Configuration of Display Color Selection
Press
a
until the
COLR
Display Color Selection Menu
appears on the Display. Configure
COLR
as
N.CLR
/
GRN
(green),
1.CLR
/
RED
(red),
2.CLR
/
AMBR
(amber). Please
refer to the operator’s manual if needed.
Step 39. Run a Test
Press
a
until reset the controller and return to RUN Mode
to display
075.0
(Ambient Temperature). Now you are
ready to observe temperature as it rises 10°F higher than
displayed. Touch the tip of the Thermocouple to raise the
temperature above the Alarm 2 High value
082.0
, and AL2
will turn on, and Display Color will change from Green to
Amber. Continue touching the tip to raise the temperature
above the Alarm 1 High value
087.0
and Display Color will
change from Amber to Red.
Step 10. Enter to the Thermocouple Input Submenu
Press
d
to store Thermocouple Input. The display will stop
flashing and show the top menu for Thermocouple types. If
you press
a
controller will step to next menu item (Skip to Step 14).
Step 11. Enter to the Thermocouple Type Input Submenu
Press
d
to display flashing, previously selected
Thermocouple type.
Step 12. Scroll through available selection of TC types
Press
b
to sequence thru flashing Thermocouple types,
(select k -for type "K" CHROMEGA
®
/ALOMEGA
®
)
J K T E N DIN J R S B C - TC types
J k t E N dN J R S b C - Display
Step 13. Store TC type
After you have selected the Thermocouple type press
d
to
store your selection, the instrument automatically advances
to the next menu item.
Step 14. Enter to Reading Configuration Menu
The display shows
RDG
Reading Configuration, which is the
top menu for 4 submenus: Decimal Point, Degree Units,
Filter Constant and Input/Reading Submenus.
Step 15. Enter to Decimal Point Submenu
Press
d
to show
DEC
Decimal Point.
Step 16. Display the Decimal Point position
Press
d
again to display the flashing Decimal Point position.
Step 17. Select the Decimal Point position
Press
b
to select
FFF.F
Decimal Point position.
Step 18. Store selected Decimal Point position
By pressing
d
momentarily the Decimal Point position will
be stored and the instrument will go to the next menu item.
Step 19. Enter to Temperature Unit Submenu
Display shows
TEMP
Temperature Unit.
Step 20. Display available Temperature Units
Press
d
to display the flashing Degree
°F
or
°C
.
Step 21. Scroll through Temperature Units selection
Press
b
to select
°F
Degree.
Step 22. Store the Temperature Unit
Press
d
to display momentarily that the Degree Unit has
been stored and the instrument will go automatically to the
next menu item.
Step 23. Enter the Filter Constant Submenu
Display shows
FLTR
Filter Constant Submenu.
Step 24. Display the Filter Constant Value Submenu
Press
d
to display the flashing, previously selected Filter
Constant.
Step 25. Scroll through available Filter Constants
Press
b
to sequence thru Filter Constants
0001
,
0002
,
0004
,
0008
,
0016
,
0032
,
0064
and
0128
.
Step 26. Store the Filter Constant
Press
d
momentarily to store
0004
Filter Constant and the
instrument will automatically go to the next menu item.
Step 27. Enter Alarm 1 Menu
The display will show
ALR1
the top menu for Alarm 1. In the
following steps we are going to enable Alarm 1, Deviation,
Unlatch, Normally Open, Active Above, Enable at power on
and +2°F High Alarm i.e. Process Value > Setpoint 1 Value
+2°F will activate Alarm 1.
Step 28. Enter Alarm 1 Enable/Disable Submenu
Press
d
to display flashing
DSBL
/
ENBL
.
MQS3448/0102
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of
one (1) year from the date of purchase. In addition to OMEGA’s standard warranty period, OMEGA Engineering will
extend the warranty period for four (4) additional years if the warranty card enclosed with each instrument is
returned to OMEGA.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will
issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA,
if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply
to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing,
operation outside of design limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit
shows evidence of having been tampered with or shows evidence of having been damaged as a result of excessive
corrosion; or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating
conditions outside of OMEGA’s control. Components which wear are not warranted, including but not limited to
contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither
assumes responsibility for any omissions or errors nor assumes liability for any damages that result from
the use of its products in accordance with information provided by OMEGA, either verbal or written. OMEGA
warrants only that the parts manufactured by it will be as specified and free of defects. OMEGA MAKES NO
OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED,
EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION
OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of OMEGAwith
respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or
otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event
shall OMEGA be liable for consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic
Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications
or used on humans. Should any Product(s) be used in or with any nuclear installation or activity, medical application,
used on humans, or misused in any way, OMEGA assumes no responsibility as set forth in our basic
WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify OMEGAand hold OMEGA harmless
from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.
RETURN REQUESTS/INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE
RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR)
NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING
DELAYS). The assigned AR number should then be marked on the outside of the return package and on any
correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in
transit.
FOR W
ARRANTY RETURNS, please have the
following information available BEFORE
contacting OMEGA:
1. Purchase Order number under which the product
was PURCHASED,
2. Model and serial number of the product under
warranty, and
3. Repair instructions and/or specific problems
relative to the product.
FOR NON-W
ARRANTY REPAIRS, consult OMEGA for
current repair charges. Have the following information
available BEFORE contacting OMEGA:
1. Purchase Order number to cover the COST of the
repair,
2. Model and serial number of product, and
3. Repair instructions and/or specific problems
relative to the product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords
our customers the latest in technology and engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2002 OMEGAENGINEERING, INC. All rights reserved. This document may not be copied, photocopied,
reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without
the prior written consent of OMEGA ENGINEERING, INC.
PATENTAND TRADEMARK NOTICE: This product is covered by one or more of the following patents: U.S. Pat.
No. Des. 336,895; 5,274,577; 6,243,021 / CANADA 2052599; 2052600 / ITALY 1249456; 1250938 / GERMANY DE
41 34398 C2 / SPAIN 2039150; 2048066 / UK Patent No. GB2 249 837; GB2 248 954 / FRANCE BREVET NO. 91
12756. The “Meter Bezel Design” is a trademark of Newport Electronics, Inc. USED UNDER LICENSE. Other U.S.
and International Patents pending or applied for.
This device is marked with the international caution symbol. It is important to read the
Setup Guide before installing or commissioning this device, as the guide contains important
information relating to safety and EMC.
WARNING: These products are not designed for use in, and should not be used for, patient-
connected applications.
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply.
OEMGA is constantly pursuing certification of its products to the European New Approach Directives.
OMEGA will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct, but OMEGA Engineering, Inc.
accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.
TRADEMARK NOTICE:
®
, omega.com
®
,
,
and
™
are Trademarks of
OMEGA ENGINEERING, INC.
®
SPECIFICATION
Accuracy:
+
0.5°C temp;
0.03% rdg. process typical
Resolution:
1
°
/0.1
°; 10 µV
process
Temperature Stability:
0.04°C/°C RTD;
0.05°C/°C TC @ 25°C (77°F);
50 ppm/°C process
Display:
4-digits, 9-segments LED,
10.2 mm (0.40") with red, green and
amber programmable colors
Input Types:
Thermocouple, RTD, Analog Voltage
and Current
TC: (ITS90)
J, K, T, E, R, S, B, C, N, L
RTD: (ITS68)
100/500/1000 ohm Pt sensor
2-, 3-, or 4-wire; 0.00385 or 0.00392
curve
Voltage:
0 to 100 mV, 0 to 1 V, 0 to 10 Vdc
Current:
0 to 20 mA (4 to 20 mA)
Output 1
†
:
Relay 250 Vac @ 3 A Resistive Load,
SSR, Pulse
Output 2
†
:
Relay 250 Vac @ 3 A Resistive Load,
SSR, Pulse
†
Only with -AL option
Options: Communication
RS-232 / RS-485 or
Excitation:
24 Vdc
@ 25 mA
Not available for Low Power Option
Line Voltage/Power:
90 - 240 Vac ±10%,
50 - 400 Hz*,
or 110 - 375 Vdc, 4 W
* No CE compliance above 60 Hz
Low Voltage Power Option:
12 - 36 Vdc, 3 W**
**
Units can be powered safely with 24 Vac
but No Certification for CE/UL are claimed.
Dimensions:
25.4 H x 48 W x 126.3 D mm
(1.0 x 1.89 x 5")
Weight:
127 g (0.28 lb)
Approvals:
UL, C-UL, CE per EN50081-1,
EN50082-2, EN61010-1
Servicing North America:
USA: One Omega Drive, P.O. Box 4047
ISO 9001 Certified Stamford CT 06907-0047
TEL: (203) 359-1660 FAX: (203) 359-7700
e-mail: info@omega.com
Canada: 976 Bergar
Laval (Quebec) H7L 5A1
TEL: (514) 856-6928 FAX: (514) 856-6886
e-mail: info@omega.ca
For immediate technical or application assistance:
USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA
®
Customer Service: 1-800-622-2378 / 1-800-622-BEST
®
Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN
®
TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA
Mexico and TEL: (001)800-TC-OMEGA
®
FAX: (001) 203-359-7807
Latin American: En Espa
ñol: (001) 203-359-7803
e-mail: info@omega.com.mx
Servicing Europe:
Benelux: Postbus 8034, 1180 LA Amstelveen, The Netherlands
TEL: +31 20 3472121 FAX: +31 20 6434643
Toll Free in Benelux: 0800 0993344
e-mail: nl@omega.com
Czech Republic: Rudé armády 1868, 733 01 Karviná 8
TEL: +420 69 6311899 FAX: +420 69 6311114
e-mail: czech@omega.com
France: 9, rue Denis Papin, 78190 Trappes
TEL: +33 130 621 400 FAX: +33 130 699 120
Toll Free in France: 0800406342
e-mail: france@omega.com
Germany/Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
TEL: +49 7056 9398-0 FAX: +49 7056 9398-29
Toll Free in Germany: 0800 639 7678
e-mail: germany@omega.com
United Kingdom: One Omega Drive
ISO 9002 Certified River Bend Technology Centre
Northbank, Irlam Manchester M44 5BD United Kingdom
TEL: +44 161 777 6611 FAX: +44 161 777 6622
Toll Free in England: 0800 488 488
e-mail: sales@omega.co.uk
OMEGAnet
®
On-Line Service
www.omega.com
Internet e-mail
info@omega.com
®
®
i/32 Temperature & Process
Monitor/Alarm