Filter
Top Products
4 To advance the day setting by 1, press the HOUR/MSF button once.
5 To advance the month setting by 1, press the MINUTE button once.
6 If an incorrect date is entered after advancing the month, like Apr 31st 2001,
the date will be set to the maximum day of that month, which is Apr
30th 2001, automatically.
7 Press the TIME button to return to time mode. If you do not press any
buttons for 15 seconds the clock will return to time mode.
Reviewing the day of the week
1 Press and hold the TIME button for 3 seconds in time mode, the current
year is displayed.
2 Press the SNOOZE button twice to review the day of the week, the day will
appear on the display, dAY1 ... dAY7 will be displayed which stands for
Monday to Sunday respectively. The day of the week cannot be changed but
it is already set according to the date.
3 Press the TIME button to return to time mode. If you do not press any
buttons for 15 seconds the clock will return to time mode.
MSF Signal
1 This mode starts when the HOUR/MSF has been pressed in time mode,
‘-0 0-‘ displays.
2 If you want to review the current time when receiving MSF signal, press the
TIME button.
3 Press the HOUR/MSF to alternate between MSF on mode and off.
4 When the MSF signal is detected the two digit counter will count up steadily
from 00 to 59, until the clock is synchronised.
Note : If the two digit counter is not counting up, then it is not receiving the
MSF signal, change the position of the unit for the best reception.
5 When the TIME button is pressed or when a valid MSF signal has been
received the clock will return to time mode.
6 The unit will automatically synchronize at 12.00am and 3.00am everyday.
To stop the alarm tone (Alarm 1 and 2 have individual alarm tones).
The alarm is programmed to run for 59 minutes.
1 To stop the alarm, press the ALARM button (6). The alarm will stop and
will operate again 24 hours later.
2 To stop the alarm temporarily, press the SNOOZE button (4). The alarm
will sound again 9 minutes later.
3 To switch the alarm setting off press the ALARM button once and release.
Then press the snooze four times until the display reads --:--. Repeat if
necessary for alarm 2. Neither indicator (8 or 9) should be illuminated.
Snooze function
Once you have activated the snooze, the alarm will sound again after 9 minutes.
1 Press the SNOOZE button (4), after 9 minutes the alarm
buzzer will sound again.
Maintenance
Do not expose your clock to extremes of temperature. The product should
be kept in a warm environment free from dust and damp. For external cleaning
use only a soft, clean, damp cloth. Use of detergents may damage the finish.
Technical specification
AC Power supply : 230v AC 50Hz
Battery back-up : 4.5V DC type 3 x AA (not included)
ATTENTION: To reduce the risk of electric shock, do
not remove the cover. There are no user
serviceable parts inside the unit. Refer any
servicing to qualified personnel.
The lightning flash with arrowhead symbol within the triangle is a
warning sign alerting the user of ‘dangerous voltage’ inside the
unit.
The exclamation point within the triangle is a warning sign alerting
the user of important instructions accompanying the product.
To prevent fire or shock hazard do not expose this apparatus to
dripping and splashing.
Guarantee
Morphy Richards products are manufactured to internationally accepted quality
standards. In addition to your statutory rights, Morphy Richards guarantee your
product to be free from manufacturing and component defects for a period of TWO
YEARS from date of purchase.
If your product proves to be defective within 28 days of purchase, your Morphy
Richards dealer from whom the product was purchased will be pleased to replace it
free of charge.
Should your product develop a defect within the guarantee period but after the
replacement period, please return the product to the following address, together with
the proof of purchase, brief details of the symptoms and your own name and
address.
Morphy Richards Limited
Talbot Road
Mexborough
South Yorkshire
S64 8AJ
Your post office will provide a certificate of posting. The product will be repaired
and returned to you promptly.
If you need any further advice, please call our Helpline (UK local rate)
on: 08450 777700 (Mon-Fri)
Morphy Richards Website: www.morphyrichards.co.uk
446/8001/75 Rev 2
Imported by : Morphy Richards Ltd, Talbot Road, Mexborough, S64 8AJ
Morphy Richards products are intended for household use only.
Morphy Richards has a policy of continuous improvement in product quality and design.
The company, therefore reserves the right to change the specification of its models at any time.
3 Press the HOUR/MSF to adjust the alarm time by + 1 hour, press and hold
HOUR/MSF to adjust the alarm clock by 5hrs/0.5 seconds.
4 Press the MINUTE button to adjust the alarm time by + 1 minute, press and
hold the MINUTE button to adjust the alarm clock by 5 min/0.5 seconds.
5 To exit the alarm setting, press the TIME button once, or wait for 15 seconds
the display will revert back to the time.
The alarm will activate at the set alarm time.
The alarm will automatically turn off after 59 minutes.
Setting the alarm 2 time
1 Press the ALARM button twice in time mode. ‘AL 02’ will display when alarm is
pressed.
2 Repeat the same procedure as used for alarm 1.
Viewing the previous alarm type
1 Press the ALARM button to select the setting for alarm 1 or alarm 2.
2 Press and hold the SNOOZE button, the previous alarm type displays.
Note : Do not press the SNOOZE button again, otherwise, the type of alarm
will be changed.
3 Press the TIME button, to exit the alarm setting mode. (The alarm mode will
also exit if no buttons are pressed for 15 seconds).
Reviewing / setting the year
1 Press and hold the TIME button for 3 seconds in time mode, the current
year will be displayed.
2 Press the MINUTE button once to change the year in the following sequence:
1999-2000 - ... - 2048 - 2049 -1950 -1951 - ... - 1999 - 2000
3 Press the HOUR/MSF to change the setting by 10 years.
4 If an incorrect date is entered after advancing the year by one, like Feb
29th 2001, the date will be set to the maximum day of that month, which is
28th Feb 2001 automatically.
5 Press the TIME button to return to time mode. If you do not press any
buttons for 15 seconds the clock will return to time mode.
Reviewing / setting the date
1 Press and hold the TIME button for 3 seconds in time mode, the current
year will be displayed.
2 Press the SNOOZE button once for review / setting the date mode.
3 The date will display, in ddmm format.
P. 5 P. 6
P. 7
Warning labels
WARNING: to reduce the risk of electric shock, do not expose this
appliance to rain or moisture.