JVC RD-EZ11 Portable CD Player User Manual


  Open as PDF
of 2
 
Program playback
3 Set the source to AUDIO IN.
4 Start playing the equipment.
5 Adjust the volume.
Up to 20 tracks can be programmed to play in a
desired order.
To program the playing order
While playback is stopped...
1 Show the program creation display.
• Now you can select the first track of the
program.
2 Select a desired track.
3 Add the track to the program.
• The next program number appears on the
display, then track selection display is shown.
1 Load a disc.
2 Set the source to CD.
3 Start playback.
To select a track
To locate a desired position on the disc
During playback...
4 Adjust the volume.
To stop playback
To pause playback
• To resume, press the same button again.
1 Turn the volume to minimum.
2 Connect the equipment.
• Connect the equipment with the stereo
mini plug (3.5 mm (3/16 in) diameter) to
the AUDIO IN jack on the rear.
1 Set the source to TUNER.
2 Select the band—FM or AM.
3 Select a station.
4 Adjust the volume.
Turn the VOLUME knob to increase or decrease the
volume.
• Set the volume to minimum when you turn on the
unit.
TUNER OPERATIONS
When an FM stereo (FM ST) broadcast is hard to receive or noisy, select the monaural reception
(MONO).
• To restore stereo reception, switch to FM ST.
FM
GENERAL CONTROLS
DISC OPERATIONS
Decrease
Slide the FUNCTION selector to select CD, TUNER
or AUDIO IN.
Increase
Slide the FUNCTION selector to OFF.
Moves to indicate the
current frequency
Press and hold
Disc holder
Radio controls
Disc controls
Display
Volume knob and
function selector
The total number of
tracks
The current track
number
4 Repeat steps 2 and 3.
• When the 20th track is programmed, “- - -”
flashes on the display and the 21st track
cannot be programmed.
5 Start playback.
• After program playback ended or stopped, the
program playback mode is automatically canceled.
(The PROGRAM indicator disappears from the
display.)
To play back the program again, press PROGRAM,
then PLAY/PAUSE 6.
To edit the program
1 While playback is stopped, press PROGRAM
repeatedly to select the program number of the
track you want to replace.
• To add a track at the end of the program, select
the last program number.
2 Perform steps 2 and 3 on the left column to select
a new track.
To erase the entire program
While playback is stopped...
1 Press PROGRAM.
• PROGRAM indicator lights up on the display.
2 Press 7.
• The entire program is also erased in the following
cases:
– when you open the disc holder.
– when the unit is turned off.
– when you select another source.
Select the desired playback mode.
Each time you press the button, the playback
mode changes as follows:
Indicator Playback mode
REPEAT Repeats the current track.
REPEAT ALL Repeats all tracks.
RANDOM Plays tracks at random.
To cancel, press the same button repeatedly until
the indicator above disappears from the display.
• Repeat playback is also canceled if the playback
is stopped.
• Random playback cannot be used during
program playback. If you program the playing
order during random playback, random
playback is canceled.
LISTENING TO OTHER
EQUIPMENT
Selecting the source to play
CD:
To play back a disc. (See “DISC OPERATIONS.”)
TUNER:
To listen to the radio broadcast. (See “TUNER
OPERATIONS.”)
AUDIO IN:
To listen to the other equipment connected to
the AUDIO IN jack. (See “LISTENING TO OTHER
EQUIPMENT.”)
Adjusting the volume Turning the unit off
Basic procedure
Basic procedure
Basic procedure
Repeat/Random playback
Playback mode indicator (See below.)
Program number
Program number
AM
The AM antenna is built in, so adjusting the
position of the unit may help AM reception.
Improving the FM reception
Adjusting the antenna
RD-EZ11[J].indd 2RD-EZ11[J].indd 2 09.5.8 4:57:36 PM09.5.8 4:57:36 PM
 previous