Harman-Kardon HKS 6 Portable Speaker User Manual


 
4 MOUNTING OPTIONS
MOUNTING OPTIONS
T
he satellite speakers
may also be wall-
mounted using the
supplied brackets.
Wall-Mounting
Unscrew the bolt that attaches the black
shelf stand to the bottom of the speaker.
Store the stand and bolt in a safe place
in case they are needed for a future
installation.
Mount the wall-
bracket attachment
plate on the wall in
the desired location.
If possible, position
the speakers so that the mounting screws
(not included; use size #8) may be
installed directly into a wooden wall stud.
If that is not possible, use optional wall
anchors that are rated to support at least 25
pounds.
The customer is responsible for
proper selection and use of mounting hard-
ware
, available through hardware stores, to
properly and safely wall-mount the speakers.
Referring to the speaker connection instruc-
tions on Page 5, thread the appropriate
speaker cable through the opening in the
bottom of the wall plate, and then through
the back of the bracket as shown in the
diagram.The bracket has two openings on
top: a round screw hole, and an
arc-shaped
opening in front of it.The speaker
cable
should be threaded through the arc-shaped
opening, not the screw hole.
Attach the bracket to the wall plate by insert-
ing the tab at the top of the wall plate into
the slot on top of the bracket and snapping
the bracket onto the wall plate.
Thread the cable through the round opening
in the terminal cover, and then insert the
speaker wires into the terminals on the
underside of the speaker, remembering to
observe the correct polarity (see Page 5).
Place the terminal cover over the opening
on the underside of the speaker so that it fits
flush against the speaker and covers the ter-
minals, with its round opening exposing the
threaded insert.
The bracket fits through the
round opening in the terminal cover.
Insert the supplied bracket bolt up through
the bottom of the bracket and terminal
cover, and screw it into the threaded insert
on the underside of the speaker.The bolt
should be snug, but not so tight as to
prevent the bracket from pivoting.
The wall-mounted speaker may be pivoted
from side to side; however, the bracket is
not designed to tilt up or down, and
attempting to tilt it will damage the bracket
and possibly the wall, which would not be
covered by your warranty.
The satellite speakers may
be placed on a shelf. Place
each satellite speaker on
one of the supplied coasters
for added stability and to
protect your furniture.
W
all Plate
Remove
Stand
15mm
or 1/2"
W
all
Wall Plate
Wires to Speaker
Terminal Cover
Overhead
View
Wire
From
Wall
Plate
23mm
or 3/4"
(M6–1.25P
o
r 1/4"–20)
Wall Plate
Remove
S
tand
1
5mm
or 1/2"
Wall
W
all Plate
Wires to Speaker
Terminal Cover
Overhead
View
Wire
From
Wall
Plate
2
3mm
o
r 3/4"
(
M6–1.25P
or 1/4"–20)
Wall Plate
Remove
Stand
15mm
or 1/2"
Wall
Wall Plate
Wires to Speaker
Terminal Cover
Overhead
View
Wire
From
Wall
Plate
23mm
or 3/4"
(M6–1.25P
or 1/4"–20)
Wall Plate
Remove
Stand
15mm
or 1/2"
Wall
Wall Plate
Wires to Speaker
Terminal Cover
Overhead
View
Wire
From
Wall
Plate
2
3mm
o
r 3/4"
(M6–1.25P
or 1/4"–20)
Wall Plate
Remove
Stand
15mm
or 1/2"
Wall
Wall Plate
Wires to Speaker
Terminal Cover
Overhead
View
Wire
From
Wall
Plate
23mm
or 3/4"
(M6–1.25P
or 1/4"–20)
HKS 6 OM 10/20/06 10:17 AM Page 6