Filter
Top Products
For Warranty Information and the most up-to-date version of this User’s Guide, go to www.gpx.com Customer Service: 1-888-999-4215
Copyright © 2012 Digital Products International (DPI, Inc.) All other trademarks appearing herein are the property of their respective owners. Specications are subject to change without notice.
1. Press the Power button
to turn the unit off.
2. Press and hold the Stop/Clock
button until the display begins to
blink, then release the button.
3. Press the Tune +/- buttons
to adjust the hour.
The PM indicator will light when
the hour is set in the PM.
4. Press the Stop/Clock button.
5. Press the Tune +/- buttons
to adjust the minute.
6. Press the Stop/Clock button
to nish setting the time.
1. Press the Power button
to turn the unit off.
2. Press and hold the Al1 or Al2
button until the display begins to
blink, then release the button.
3. Press the Tune +/- buttons
to adjust the hour.
The PM indicator will light when
the hour is set in the PM.
4. Press the the Al1 or Al2 button.
5. Press the Tune +/- buttons
to adjust the minute.
6. Press the the Al1 or Al2 button.
7. Press the Tune +/- buttons to
switch between Buzzer, AM
Radio, FM Radio and CD.
The display will indicate the following:
rF-FM Radio, rA-AM Radio, bb-Buzzer
and Cd-CD.
Use the Vol+/- buttons to
adjust the volume of the alarm,
except when set to Buzzer.
8. Once the set alarm time is
reached, the alarm will sound.
To set the other alarm, follow
the above steps and choose
the alarm not currently set.
1. Press the Power button
to turn the unit on.
2. Press the Source button to switch
between the AM and FM radio mode.
3. Press the Tune +/- buttons to adjust
the radio to the desired frequency.
4. Press and hold the Tune +/- buttons to
search for the next available frequency.
5. Press the Vol+/- buttons to
adjust the volume.
6. Press the Power to turn the radio off.
Clock and Sleep Timer Alarm Radio
Setting the Clock Setting the Alarm
1. Follow the instructions for Setting the
Alarm.
2. Press the Al1 or Al2 button until the
indicator is no longer lit.
Cancelling the Alarm
After the alarm sounds:
Press the Snooze/Dimmer button to delay the
alarm for several minutes.
OR
Press the Power button to turn the alarm off
until the set alarm time is reached again.
Snooze and Alarm Reset
Tuning the AM or FM Radio
1. Follow the instructions for Tuning the AM
or FM Radio.
2. Tune to the desired station.
3. Press the Al 2/Program button.
The display will ash.
4. Press the Tune +/- buttons to set as P1
- P10.
5. Press the Al 2 /Program to nish setting
the station as a preset.
Saving a Station as a Preset
1. Follow the instructions for Tuning the
Radio and Saving a Station as a Preset.
2. Press the Play/Pause/Mem+ button to
cycle through preset radio stations.
Tuning to a Preset Radio Station
Extend the FM Antenna to improve FM radio
reception.
An AM antenna is built into the clock radio. To
improve AM radio reception, adjust the position
of the clock radio.
Radio Reception
To download this User’s Guide in
English, Spanish, or French, or to get
answers to frequently asked questions,
visit the support section at:
www.gpx.com
Para descargar este Manual del
Usuario en inglés, español y francés, o
para obtener respuestas a preguntas
frecuentes, visite la sección de apoyo en
www.gpx.com
Pour télécharger ce guide de l’utilisateur
en anglais, espagnol ou français,
ou pour obtenir des réponses à des
questions fréquemment posées,
consultez la rubrique d’assistance sur
www.gpx.com
International Support
1. Open the CD Door.
2. Place a CD into the boombox,
label side facing up.
3. Close the CD Door.
CD
Loading a CD
1. Follow the instructions for Loading a CD.
2. Press the Source button to
switch to CD mode.
3. Press the Play/Pause button to
begin playing the loaded CD.
Playing a CD
1. Follow the instructions for Loading
a CD and Playing a CD.
2. Press the Stop button to stop
the CD during play.
3. Press the Program button.
“1--” will begin to blink on the display.
4. Press the Tune +/- buttons
to select a track.
5. Press the Program button to save
the selected track to the program.
6. Repeat steps 4 and 5 to
program up to 20 tracks.
Programming a CD
Requires a 3.5mm audio cable (not included).
1. Connect a 3.5mm audio cable to the
AUX Input and the audio output on an
MP3 player or other audio device.
2. Press the Source button to
switch to AUX mode.
3. Use the native controls on the connected
MP3 player or other audio source to play
your audio through the CD Clock Radio.
AUX input
Using the Audio Input
Requires a USB cable (not included).
1. Make sure the unit is plugged into the wall.
2. Using the appropriate USB charging
cable (not included), connect one
end to the device and the other
to the USB Port on the unit.
Refer to the user’s manual for your
specic device for manufacturers
required charging amperage as well
as determining the appropriate cable
for your device before charging.
3. The device will now charge.
Note: Refer to the user’s manual for your
specic device for manufacturers required
charging amperage. High-ameperage
devices such as iPads will not charge.
USB
Charging a Device with the USB Port
1. Follow the instructions for Setting the
Clock.
2. Press the Snooze/Sleep button
repeatedly to set the sleep timer ( 90, 80,
70, 60, 50, 40, 30, 20, 10 min or OFF ).
3. Once the set sleep time has expired the
clock radio will automatically power off.
Setting the Sleep Timer