Filter
Top Products
Turn LARGE Knob to change MHz
Turn SMALL Knob to change kHz
Press <-> to toggle Active & Standby
Press MON to monitor Standby
Press MEM to memorize Standby
Press RCL to recall stored frequencies
Press COM
Turn the LARGE Knob to view
frequency types
Turn the SMALL Knob to view
frequencies for selected type
Comm Radio (COM)
Active FPL
FPL #1
.
.
.
FPL #30
Create New FPL
Turn LARGE Knob
Press FPL
Flight Plan (FPL)
Press MSG
New
Old
Turn LARGE Knob
Turn SMALLKnob
New Msg 1
.
.
.
New Msg n
Turn SMALLKnob
Old Msg 1
.
.
.
Old Msg n
Messages (MSG) Database (DB)
Create WPT by Lat/Lon
Create WPT by Radial/Dist
Update User Wpt w/PPos
Create Wpt by User Grid*
Delete User WPT
Modify User WPT
Delete WPT Comment
Access Database
Turn LARGE Knob
Press DB
* when enabled
Press SYS. Turn LARGE Knob, then press ENTER.
Nav Info
Autonav Time
Lat/Lon Units
Program Nav Pages
Mag Var
Flight Timer Trigger
Direct-To
CDI Scaling
Turn LARGE Knob
System (SYS)
System Info
Date/Time
Test Display
Display Brightness
Owner Name
Model, SW Ver, S/N
Fuel Units
Baro Units
Turn LARGE Knob
GPS Sensor
Healthy & Visible
Satellites
Satellites Used for Fix
Satellite Search Status
GPS Date & Time
GPS Normal Reset
Turn LARGE Knob
Misc Sensors
Encoding Altimeter
Air Data Info
Fuel Info
Turn LARGE Knob
Comm Info
RF Signal Level
Noise Level
Intercom Squelch Mic1
Intercom Squelch Mic2
Transmit
Intercom Level
Sidetone Level
Headphone Level
Turn LARGE Knob
Enroute
Within 30 nm of
Destination
IAF Active Waypoint
FAF Active Waypoint
At FAF (MAP Becomes Active)
At MAP (TO/FROM Transition)
MAHP Active Waypoint
Load Approach
Enable Approach & enter altimeter setting
(Approach annunciator turns ON)
(CDI goes to 1 nm full-scale sensitivity)
Verify Approach annunciator is ON
Verify/Set OBS/HLD: ON for Procedure Turn or Hold
OFF to sequence
Verify green Approach-Active annunciator is ON
Verify altimeter setting is entered
Verify/Set OBS/HLD: OFF to sequence to MAP
Verify Approach-Active annunciator is ON
(CDI goes to 0.3 nm full-scale sensitivity)
If NOT landing: Press OBS/HLD to cancel
Approach-Active
(Green Approach-Active annunciator turns OFF)
(Approach Annunciator remains ON)
(CDI goes to 1.0 nm full-scale sensitivity)
Verify OBS/HLD is ON
Location Action
Approach Checklist
GX60 Only
DME-Arc Checklist
At Arc
Intercept
On Arc
Inbound Leg
Intercept
1. Verify/Set OBS/HLD ON
2. USE DME-Arc Page in NAV mode
3. Verify or select DME-Arc Reference Waypoint and follow the
prompts
4. Use Nav or Map mode and follow information
1. Use DME-Arc page in NAV mode or Map mode to navigate
2. Follow prompts for inbound leg intercept
1. Follow prompts to turn to next leg
Location
Action
GX60 Only
Approach Setup Summary
B. Load Approach Information
Load a destination airport. Load a stored
Flight Plan, or edit the active Flight Plan.
You may also use the DIRECT-TO button
to choose a destination. The destination
must be an airport that has an established
approach capability.
A. Load Destination Airport
GX60 Only
1. Press FPL twice to reach the home page
Flight Plan Mode and press SEL, or
press SEL while in the Nav function.
2. Press ENTER to prepare to load
approach waypoints.
3. Turn the SMALL knob to display the
available approach choices.
4. Press ENTER to select the displayed
approach path.
5. Turn the SMALL knob to display the
approach legs.
6. Press NAV to return to Navigation Mode.