Filter
Top Products
Definitive Technology
SSA-42
OWNER’S MANUAL
5. Use a bubble level to make sure the template is level. If the
TV is wall mounted and not level, the speaker will look better
if it is off-level in exactly the same way as the TV.
6. Use push pins to secure the template to the wall.
7. Mark the location of pilot holes noted on the Mounting
Template with a pencil; remove the template.
8. Pre-drill the pilot hole locations for mounting screws
(not included). Use screws rated to hold securely in the
wall material (we recommend #10 screws).
9. It is best if at least one screw hits a wall stud. If there is no
stud behind the pilot hole location, install wall anchors (not
included) to secure the bracket screws. Follow the wall anchor
manufacturer’s directions. Each wall anchor should be rated
to hold at least one-half of the product net weight
[see specifications on front cover].
10. For masonry walls, use a masonry drill bit to pre-drill holes,
and use masonry anchors and screws (not included).
11. Pull the five sets of speaker wires through the hole in the bracket.
12. Screw the bracket to the wall.
Wall Mounting the SSA
• We recommend that the SSA speaker be wall mounted
by professional installers or by those appropriately skilled in the
use of power tools and who have knowledge of building codes
and structural issues.
• We recommend that you determine a suitable location for
your speaker installation, and that you complete all wiring
(especially “hidden” in-wall wiring) before mounting the
bracket to your wall.
• Mythos Brackets are not suitable for ceiling mounting.
The Mythos Solo Surround Array loudspeaker comes with a wall
mounting bracket and template that makes secure mounting a breeze.
Follow these directions for installing the wall mounting bracket.
1. Two
1
⁄4"–20 screws have been factory installed on the back of the
speaker. Gently hand-turn the screws to make sure they are in as
far as they can go. Do not force them beyond the “stop” point.
The screws cannot screw all the way into the speaker and should
protrude as shown in the illustration.
2. Make sure the location you have selected for wall-mounting
does not conceal behind-wall electrical wiring or plumbing.
3. Hold the cardboard template (included) in the intended
location. Make sure the speaker clears the ceiling, adjacent
walls, corners, beams, lighting fixtures and door/window
frames. Leave at least 1
1
/
2
" (38 mm) above the speaker location
to allow the speaker to slide down onto the bracket.
4. Make sure the center of the template is perfectly centered with
the TV screen.
Positioning the SSA
The SSA speaker may be mounted on
the wall above or below the video screen.
It may be placed on a table or shelf
in front of the TV.
If placed on a shelf under a TV, adjust the
leveling feet (screwed all the way in) to
aim the speaker up towards the listeners.
The SSA speaker may be placed directly
on top of TVs that have at least 5-inches
(13 cm) of flat surface on top. Do not
place the SSA speaker on top of any
surface that is not large or stable enough
to securely support the speaker. If the
speaker seems at all unstable or “tipsy”
place the speaker somewhere else. The
warranty does not cover damage
caused by falls due to improper
positioning of the speaker. If the
speaker is above seated listener height,
extend the leveling feet to point the
speaker downward [See Using the Leveling
Feet on page 3].
SSA-42 Mounting Screw Diagram
BACK OF SPEAKER
TOP OF SPEAKER
1
/"–
4
20 SCREWS
THREADED INSERTS
+
SURROUND RIGHT – + FRONT RIGHT – + CENTER – + FRONT LEFT – + SURROUND LEFT –
2
Revised Ar twork: SSA-42 Manual Wall Bracket Template
PILOT SLOTS
Even if you intend to place the SSA speaker on a TV or shelf you must attach the wall-mount bracket to the speaker. See Using the Leveling Feet on page 3.