Filter
Top Products
CD OPERATION
Set the FUNCTION Selector to the CD position and insert a CD.
1. Press PLAY/PAUSE button to play.
2. Press PLAY/PAUSE button to pause while in play mode.
3. Press PLAY/PAUSE button once more to resume play.
4. Press STOP to stop play.
5. Always press STOP and wait for complete stop to remove CD
from CD player.
Play/Stop/Pause Mode
1. Slide the Function Selector switch to radio.
2. Select the desired AM or FM with the band switch.
3. Tune the desired station by turning the Tuning Control.
4. Adjust the volume with Volume Control as desired.
5. Extend Telescopic Antenna and adjust the direction and angle
to obtain the optimum reception.
6. Set the Function Switch to Tape for power standby mode.
RADIO OPERATION
You can use headphones with 3.5mm diameter stereo plug and
have impedance of 32ohms. When the headphones are con-
nected, the speakers are disconnected automatically.
Set the VOLUME to a low level before using headphones and
gradually adjust the Volume Control to the comfortable listening
level.
Do not play the VOLUME too loud for extended periods of time
to avoid any damage your hearing.
HEADPHONES (Not included)
1. Press Repeat button once to repeat current track only,
the indicator is lighting and keeping on. twice to repeat
all tracks, the indicator is flashing.
2. Press Repeat button twice to cancel repeat current track.
Or once to cancel repeat all tracks.
Repeat Mode
Tracking Mode
1. To go back to beginning of current track, press once.
2. To go back to previous tracks, press repeatedly.
3. To go to next track, press once or repeatedly to play
your desired track.
We recommend that you use only type1 (Normal Bias)
cassette tape with your tape player.
CASSETTE TAPE OPERATION
1. Set the FUNCTION Selector to the TAPE (OFF) position.
2. Press STOP/EJECT to open the tape deck door. Insert
a tape and close the door.
3. Press PLAY to start play, the tape will stop automatically
at the end.
4. Press to rewind or press to fast forward tape.
This unit is equipped with ALC (Automatic Level control) cir-
cuitry that automatically sets the recording to the optimum level.
Adjusting the VOLUME control does not effect the recording.
RECORDING FROM RADIO/CD
Recording from Radio
1.Set the FUNCTION Selector to the RADIO position.
2.Set the BAND Selector to AM or FM.
3.Turn the TUNING Dial to tune in a radio station.
4.Open the cassette deck door and insert the blank tape.
5.Press PAUSE, then press RECORD, the PLAY key is automati-
cally engaged with RECORD button.
6.Release the PAUSE button to begin recording. You can use the
PAUSE button to edit any unwanted commercials or programs
during your recording.
7.Recording will stop automatically at the end of the tape or
press STOP to end the recording manually.
Recording from CD
1.Set the FUNCTION selector to the CD position.
2.Insert a CD.
3.Open the cassette deck door and insert the blank tape.
4.Press RECORD and the PLAY key is automatically engaged.
5.Press the PLAY/PAUSE button on the CD player, the Play/Pause
indicator will illuminate.
6.Press the STOP button to manually end recording or it will stop
automatically at the end of recording.
SPECIFICATIONS
Power Sourc
Speakers
Output Power
Weight
: AC 110/220V 50/60Hz 10W DC 12V
(8x"D" size batteries)(not included)
: 4" Wide range, 4ohm
: 2x2W
: 8 lbs ( batteries not included)
Tape Player/Recorder
Tape : Standard normal bias
Frequency Response : 125-6300Hz
Radio
Frequency Response : FM 88-108MHz
AM 530-1600KHz
Laser Wavelength : 760-800NM
Tracking Method : 3-spot error detection/3.86mm lens
CD Player
5. Press STOP/EJECT to stop play.
6. Press STOP/EJECT one more time to open the cassette
door and take the tape out.
7. Adjust the sound with the VOLUME control.
To program:
(1) Press REPEAT button at stop mode,”REPEAT”
indicatorlight will flash, the serial number for
programming frozen at the same time.
(2) Press FF (orREW )button to select the track
number.
(3) When desired track is displayed, press REPEAT
button to confirm.
(4) Repeat (2)~(3) to set up 16 tracks. The display
will show the current set track.
(5) Set tracks can be reviewed by pressing REPEAT
button.
(6)
Program Function
To complete the programming and to play,
press PLAY/PAUSE button to start the
programmed tracks.
(5) To clear the programming, press STOP( )
button.
(REPEAT function will change
into PROGRAM function at stop mode)
We recommend that the unit be powered by AC (house current)
when recording since this function uses the most power. We re-
commend that you use Type 1 (normal bias) cassette tapes only.
Note: After setting up to 10 tracks(P0-P9), the letters
"a-b-c-d-e-f"(Pa-Pf) will replace the digits "11-12-13-14
-15-16", because the LCD can only display
two digits at most.