Filter
Top Products
Operation Guide 3219
E-59
To perform an elapsed time operation
D D D D A
Start Stop (Restart) (Stop) Reset
To pause at a split time
D
A A D A
Start Split
(SPL displayed)
Split release Stop Reset
To measure two fi nishes
D
A D A A
Start Split
(SPL displayed)
First runner fi nishes.
Display time of fi rst
runner.
Stop
Second runner
fi nishes.
Split release
Display time of
second runner.
Reset
E-58
Using the Stopwatch
The stopwatch measures elapsed time, split times, and two fi nishes.
To enter the Stopwatch Mode
Use C to select the Stopwatch Mode (ST) as shown on
page E-39.
Hours
1/100 second
Minutes Seconds
E-57
To turn an alarm and the Hourly Time Signal on and off
In the Alarm Mode, use 1. D to select an alarm or the
Hourly Time Signal.
When the alarm or the Hourly Time Signal you want is 2.
selected, press A to toggle it between on and off.
The alarm on indicator (when any alarm is on), snooze x
alarm indicator (when the snooze alarm is on), and the
Hourly Time Signal on indicator (when the Hourly Time
Signal is on) are shown on the display in all modes.
To stop the alarm
Press any button.
Hourly time signal
on indicator
Snooze alarm indicator
E-56
While a setting is fl ashing, use 4. D (+) and B (–) to change it.
When setting the alarm time using the 12-hour format, take care to set the time x
correctly as a.m. (no indicator) or p.m. (P indicator).
Press 5. A to exit the setting screen.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-55
To set an alarm time
In the Alarm Mode, use 1. D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
AL1 AL3 SNZAL2 AL4 SIG
DDDDD
D
Hold down 2. A for about two seconds until the alarm
time starts to fl ash. This is the setting screen.
Press 3. C to move the fl ashing between the hour and
minute settings.
Alarm ON/OFF indicator
E-54
To enter the Alarm Mode
Use C to select the Alarm Mode (AL) as shown on page E-39.
There are four alarm screens numbered
x AL1, AL2, AL3 and AL4 for the daily
alarm, and a snooze alarm screen indicated by SNZ. The Hourly Time Signal
screen is indicated by SIG.
When you enter the Alarm Mode, the data you were viewing when you last exited
x
the mode appears fi rst.
E-53
Using the Alarm
You can set fi ve independent daily alarms. When a daily
alarm is turned on, an alarm tone will sound for about
10 seconds each day when the time in the Timekeeping
Mode reaches the preset alarm time. This is true even
if the watch is not in the Timekeeping Mode. One of
the alarms is a snooze alarm, while the other four are
one-time alarms. The snooze alarm repeats every fi ve
minutes.
You can also turn on an Hourly Time Signal, which will
cause the watch to beep twice every hour on the hour.
Alarm number
Alarm time
(Hour : Minutes)
E-52
To specify standard time or daylight saving time (DST) for a city
In the World Time Mode, use 1. D (East) to display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
Hold down 2. A for about two seconds until the watch
beeps.
This toggles the city code you selected in step 1
x
between Daylight Saving Time (DST indicator
displayed) and standard time (DST indicator not
displayed).
Using the World Time Mode to change the DST setting of the city code that is
x
selected as your Home City also will change the Timekeeping Mode time DST
setting.
Note that you cannot switch between standard time/daylight saving time (DST)
x
while UTC is selected as the World Time City.
The standard time/daylight saving time (DST) setting affects only the currently x
selected time zone. Other time zones are not affected.
DST indicator
E-51
Checking the Current Time in a Different Time Zone
You can use the World Time Mode to view the current
time in one of 29 time zones (48 cities) around the globe.
The city that is currently selected in the World Time Mode
is called the “World Time City”.
To enter the World Time Mode
Use C to select the World Time Mode (WT) as shown
on page E-38.
To view the time in another time zone
In the World Time Mode, use D (East) to scroll through
city codes.
Currently selected
World Time City
Current time in the
currently selected World
Time City
E-50
Note
For information about selecting a Home City and confi guring the DST setting, see
x
“Confi guring Home City Settings” (page E-42).
While 12-hour format is selected for timekeeping, a x P (PM) indicator will appear
for times from noon to 11:59 p.m. No indicator appears for times from midnight to
11:59 a.m. With 24-hour format, time is displayed from 0:00 to 23:59, without any
P (PM) indicator.
The watch’s built-in full automatic calendar makes allowances for different month
x
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s rechargeable battery replaced or after
power drops to Level 5 (page E-15).
The day of the week changes automatically when the date changes.
x
Refer to the pages shown below for more information on Timekeeping Mode x
settings.
Button operation tone on/off: “To turn the button operation tone on and off”
−
(page E-66)
Enabling and disabling power saving: “To turn Power Saving on and off” (page
−
E-68).