Filter
Top Products
5 7
8
6
SLEEP TIMER SETTING
SPECIFICATION
DUAL ALARM SETTING
SLEEP TIMER SETTING
RADIO RECEPTION
VOLUME ADJUSTMENT
Adjust the VOLUME control to
obtain the desired volume level
before using the unit.
SELECT BAND
1. Press “POWER ON/OFF” knob to
turn on radio.
2. Press “BAND” knob to repeatly
select FM or AM, the band
changed shown in display.
3. Press “ H...TIME SET...M /
TUNING” knob to select the
desired station.
PRESET CHANNEL
1. Press “MEMORY” knob until
“MEMORY” flashes on screen.
2. Press “PRESET +” knob to
increase channel, press
“PRESET -” knob to decrease
channel.
3. Press “MEMORY” knob to store.
FM: Extend the FM wire antenna
fully.
AM: Turn the unit to find the position
which gives the best reception.
NOTE:
Do not connect FM wire antenna to
external antenna.
1. Press “ SLEEP ” knob to set the sleep time.
2. Press “ SLEEP ” knob to repeatly select the desired time changed
cyclically as bellow.
Power requirements
Power consumption
DUAL ALARM SETTING
• The radio can wake up to alarm
with “Radio” or “Buzzer” sound
by putting switch in RADIO or
BUZZER position.
ALARM1 SETTING
1. Press “ALARM1” knob, “ ”
icon will flash.
2. Press “ MEMORY ” knob, timer
icon will flash.
3. Press “ H...TIME SET...M /
TUNING” knob to adjust Hour/
Minute.
4. Press “ MEMORY ” knob to store.
ALARM2 SETTING
1. Press “ALARM2” knob, “ ”
icon will flash.
2. Press “MEMORY” knob, timer
icon will flash.
3. Press “ H...TIME SET...M /
TUNING” knob to adjust Hour/
Minute.
4. Press “ MEMORY ” knob to store.
• There are up to 10 preset channels in each band.
• Press PRESET knob to select preset channel stored in memory.
• Operation must be in radio on.
AC 120V/60Hz
4W
NOTE:
• The clock radio will wake up to “Radio” or “Buzzer” when alarm timer
comes to the preset time. After about 10 seconds, the volume of alarm
will increase.
• To stop “Radio” or “Buzzer” sound by pressing any knob.
• The alarm will continue after 5 minutes if press the “SNOOZE” knob.
• The “Radio” or “Buzzer” sound will automatically turn off after 60
minutes if not press any knob.
• To clear the preset alarm time by pressing
“ALARM1 or “ALARM2” knob twice, until “ ” or “ ” icon flashes.
Alarm function will be cancelled automatically after few seconds.
• To activate the preset alarm time, press “ALARM1 or “ALARM2” knob
repeatly until “ ” or “ ” icon appears on the display.
• Press “ALARM1” or “ALARM2” knob to check and modify the preset
ALARM time.
• Can not set “Radio” and “Buzzer” alarms at the same time.
• The clock radio alarms only one time, if the alarm setting time of
ALARM1 and ALARM2 are same.
Specification and external appearance are subject to change
without advance notice due to continuous product improvement.
Printed in china
811-CR3891-010
RADIO RECEPTION
FOR BETTER RECEPTION
• Operation must be in radio off.
• The unit can alarm twice per day by setting different alarm time in
ALARM1 and ALARM2.
RESET FUNCTION
To delete all setting information by pressing “RESET” knob on the bottom
of unit, at the same time the system will resume the specified initial state
which set before leaving the factory.
RESET
• The power will be off automatically once unit reaches the sleep time.
• To clear the preset sleep time by pressing “SLEEP ” knob till “ ”
disappears from the display.