Philips XP AJ 3380 Clock Radio User Manual


  Open as PDF
of 2
 
Owner’s Manual
Mode d’emploi
Instructivo de manejo
AJ 3380 Clock Radio
AJ 3380 Clock Radio
PROBLEM
– Possible cause
• REMEDY
No sound
– Volume not adjusted.
• Adjust the volume.
AM broadcast cannot be received properly
– Weak radio signal.
• Rotate the set for better reception and make
sure the set is placed on a non-metallic surface.
Continuous crackling and hiss noise during AM
reception
– Interference from other electrical equipment
e.g. TV’s, computers, fluorescent lamps.
• Move the clock radio away from electrical
equipment.
Intermittent crackling sound during FM reception
– Weak signal.
• Adjust the built-in power cord aerial.
The alarm does not function
– The alarm is not set
• Set the alarm time and the alarm switch to
BUZ
or RAD.
– Volume too low for radio.
• Increase the volume.
The slumber does not function
– RADIO still in ON position.
• Switch RADIO to OFF position.
All unnecessary packaging material has been
omitted. We have tried to make the packaging
easy ta separate into three mono-materials:
cardboard (box), expandable polystyrene (buffer),
polyethylene (bags).
Your set consists of materials which can be
recycled if disassembled by a specialized
company. Please observe the local regulations
regarding the disposal of packing materials, dead
batteries and old equipment.
ENVIRONMENTAL INFORMATION
Troubleshooting
CANADA
English: This digital apparartus does not exceed the Class B limits for noise emissions from
digital apparatus as set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Français:Cet appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de Classe B prescrites dans le Régelement sur
le Brouillage Radioélectrique édicté par le Ministère des Communications du
Canada.
1. Check if the mains voltage as shown on the
type plate on the base of the set corresponds to
your local power supply.
2. Connect the power plug into the wall outlet.
The power supply is now switched on and the
numbers on the display will start to flash. You
will need to set the correct time.
3. To disconnect the set from the power
completely, withdraw the power plug from the
wall outlet.
1. Set the RADIO switch to ON.
2. Select your waveband using the BAND switch.
3. Use TUNING to find your radio station.
4. Adjust the sound with the VOLUME and DBB
controls.
5. To turn off the radio, set the RADIO switch to
OFF.
To improve radio reception
– For AM, the set is provided with a built-in
antenna which to function best should be
placed on a non-metallic surface e.g. wood,
plastic. Direct the AM antenna by adjusting the
position of your clock radio.
– For FM reception there is an antenna wire
built-in into the power cord. You should adjust
the power cord slightly to obtain optimum
reception.
Illumination brightness
– To change the brightness of the clock display
illumination adjust the BRIGHTNESS switch to
HI or LOW.
Clock display
The time is displayed using the 12-hour clock
system where the PM indicator lights up (on=PM,
off=AM) in the display.
Adjusting the time
1. Adjust the clock control to the TIME SET
position.
2. Press and hold down the 4,7 buttons to set
and adjust both the hours and the minutes.
– With your finger held down on 7, the time
will increase rapidly and continuously from
minutes to hours. Release 7 when you reach
the approximate time setting.
– Pressing 4 will allow you to adjust the time
slowly back minute by minute.
3. Release the 7 or 4 buttons when you have
reached the correct setting.
4. To safeguard the clock time from being
accidentally adjusted, turn the clock control to
the RUN position.
6:45
CLOCK
FM/AM RADIO
MAINS CONNECTION
Installation/Radio Clock Slumbering Additional Information
General
If you wish to use the alarm, then you should first
set the alarm time.Two different alarm times are
possible. This can be useful when, for example,
you need to be awakened at a different time
during the week and at the weekend. There is also
the choice of two modes for waking you up: by
buzzer or radio.
The display also indicates whether you have
switched on the alarm (s), and these indicators
will light up respectively next to ALARM 1 and
ALARM 2 on the display
1. Adjust the clock control to the ALARM 1or
ALARM 2 position.
2. Press and hold down the 4, 7 buttons to set
and adjust both the hours and minutes.
– With your finger held down on 7, the time
will increase rapidly and continuously from
minutes to hours. Release 7 when you reach
the approximate time setting.
– Pressing 4 will allow you to adjust the time
slowly back minute by minute.
3. Release the 7 or 4 buttons when you have
reached the correct setting.
4. Adjust the clock control to the RUN position to
return to clock time display.
– To review your set alarm time, adjust the
clock control to the respective ALARM 1 or
ALARM 2 position.
5. To select the alarm mode you wish to be
awoken by, set the respective ALARM 1or
ALARM 2 switch to
RAD or BUZ.
– If you have selected the radio mode, make
sure you have adjusted the volume loud
enough to wake you.
– The 2 buzzers are at a set volume and cannot
be adjusted. BUZ on ALARM 1 is a low tone
buzzer while BUZ on ALARM 2 is high tone.
You can switch off the alarm in three ways:
Unless you choose to cancel the alarm completely,
the ALARM RESET option will be automatically
selected after 59 minutes from the time your alarm
first goes off.
ALARM RESET
If you want the alarm mode to be stopped
immediately, but also wish to repeat the alarm call
at the same time for the following day:
• Press ALARM RESET during the alarm call.
REPEAT ALARM
This will repeat your alarm call at 7 minutes
intervals.
• Press
SLUMBER OFF
/REPEAT ALARM.
• Press
SLUMBER OFF/REPEAT ALARM again during
the next call if you wish to repeat the alarm
call.
• If, however, you do not press
SLUMBER
OFF
/REPEAT ALARM again, the alarm will sound
for 59 minutes before turning itself off. Your
alarm time setting will then automatically enter
the ALARM RESET mode to sound at the same
time next day.
Switching off the alarm completely
• Before or during the set alarm goes off, push
the ALARM (1 or 2) switch to the OFF position.
– The alarm indicator will disappear from the
display.
ALARM OFF
ALARM ON
SETTING THE ALARM
Alarm
AJ
33
80 AM
FM
CL
OC
K R
AD
IO
AJ3
38
0 AM FM
CLOCK RADIO
PM
ALARM
A
LARM
FM
M
H
z
88
•
9
2 • 96
• 100
•
10
4
• 10
8
M
H
z
F
M
FM
M
H
z
88
• 9
2
• 96
•
1
00
•
104
• 10
8
M
H
z
FM
A
M
k
H
z
530 630
800
1000 1300
160
0
k
H
z
AM
AM
k
H
z
530
6
30
800
10
00 1
300
160
0
k
H
z
A
M
R
E
PE
AT
A
LA
R
M
R
E
P
EAT
A
LAR
M
S
LU
M
B
E
R
• •
•
OF
F
A
L
A
R
M
R
E
S
E
T
AO
AOAO
A
O
A
O
A
O
A
O
A
O
A
A
O
A
O
A
O
dual alarm
dual alarm
3140 115 2480 1 Printed in Hong Kong TC Text/RR/9746/1
PHILIPS CONSUMER ELECTRONICS COMPANY
A Division of Philips Electronics North America Corporation
Knoxville, Tennessee 37914-1810, U.S.A.
LIMITED WARRANTY
SAFETY
The clock radio has a built-in timer device called
the SLUMBER, which enables the radio to be
automatically switched off after a set period of
time; this allows you to lie back, listen and fall
asleep. The maximum slumber time is 59 minutes.
1. Set the RADIO switch to the OFF position.
2. Set your slumber time by pressing on the
SLUMBER button. Keep your finger on the
button and the display will begin to count down
from 59 to 00 minutes.
3. Release the button as soon as the required
slumber time is reached.
You can switch off the radio before the slumber
time has elapsed:
– To cancel the SLUMBER function, press
SLUMBER
OFF
/REPEAT ALARM.
Notes:
– The slumber function does not affect the alarm
setting (s).
– If during SLUMBER you have turned down the
volume and you have an alarm set in radio
mode, make sure you have adjusted the volume
loud enough to wake you up the next day.
– If you do not intend to use the clock radio for a
long time, disconnect the set by removing the
plug from the wall outlet. The battery should
also be removed to prevent chemical leakage
which will damage your set.
– To clean your set from fingerprints, dust and
dirt, use a clean and soft damp cloth or chamois
leather. Do not use cleaning products which
contain benzene, thinner etc. as these may
harm the housing.
– When a power failure occurs, the complete
clock radio will be switched off.
– As soon as the power supply returns, the
numbers on the display will start to flash. This
indicates that you must set the correct time on
the clock.
– To retain the clock time and the set alarm time
(s) in the event of a power failure or
disconnection, insert a 9 volt battery, type 6F22
(not supplied) into the battery compartment: this
will act as a power back up. However, the time
will not be illuminated on the clock display.
Operation of the alarm (s) and FM/AM radio are
also excluded.
For clarity, the battery back up is used to retain
the set clock and alarm time (s) only.
As soon as the power supply returns, the
display will indicate the correct time.
• Before inserting the battery, connect the power
plug to the wall outlet.
• Insert a battery into the battery compartment.
– Replace the battery once a year. It is not
possible to say precisely how long the battery
will last. The service life depends on how often
and for how long the power supply fails. This
varies according to country and region.
POWER BREAKDOWN BACKUP
MAINTENANCE
SLUMBER OFF
:45
SLUMBER ON
SLUMBER
1 ALARM 1:
– BUZ (zer) – to activate buzzer for alarm 1 setting
– RAD (io) – to activate radio for alarm 1 setting
– OFF – to switch off alarm 1
2 ALARM 2:
– BUZ (zer) – to activate buzzer for alarm 2 setting
– RAD (io) – to activate radio for alarm 2 setting
– OFF – to switch off alarm 2
3 RADIO – to switch radio mode ON/OFF
4 BRIGHTNESS – to adjust the display illumination: HI-LOW
5 Display – to show the hours, minutes and
activated alarms
6 CLOCK:
– TIME SET – To adjust clock time
– ALARM 2 – To adjust/review ALARM 2
– ALARM 1 – To adjust/review ALARM 1
– RUN – To return to clock time display after
setting clock/alarm times
– 7, 4 – To adjust both the hours and minutes
(fast up, slow down) for the clock and alarm times
7 SLUMBER – to activate slumber time
8 ALARM RESET – to stop the active alarm for 24 hours
9 DBB – to select an enhanced bass sound:
Dynamic Bass Boost
0
SLUMBER OFF / REPEAT
ALARM – to switch off slumber
– to stop the active alarm for a 7 minute
period
! TUNING – to tune to radio stations
@ BAND – to select FM-AM band
# VOLUME – for adjusting the volume
$ Battery door – for power backup battery
% Power cord – for AC power supply
– antenna for FM reception
ENGLISH FRANÇAIS ESPAÑOL
Meet MAGNAVOX at the internet
http://www.magnavox.com
– réveil par la sonnerie à l’heure de réveil 1
– réveil par la radio à l’heure de réveil 1
– arrêt complet de l’alarme 1
– réveil par la sonnerie à l’heure de réveil 2
– réveil par la radio à l’heure de réveil 2
– arrêt complet de l’alarme 2
– pour allumer (ON)/éteindre (OFF) la radio
– réglage de l’éclairage de l’afficheur: HI (maxi) - LOW (mini)
– pour indiquer les heures, les minutes et les alarmes
sélectionnées
– Réglage de l’heure
– Réglage/vérification de l’alarme 2
– Réglage/vérification de l’alarme 1
– Pour réafficher l'heure d'horloge après avoir réglé
l’heure/l’alarmes
– Réglage des heures et des minutes (accéléré en avant,
ralenti en arrière) pour l’heure et l’alarme
– activation de la fonction arrêt programmé
– arrêt de l’alarme pour 24 heures
– pour accentuer les graves:
Dynamic Bass Boost
– arrêt de la fonction arrêt programmé
– arrêt de l’alarme pour 7 minutes
– accord sur l’émetteur
– choix de la bande d’ondes (FM-AM)
– réglage du volume
– pour la pile de relais
– branchement au secteur
– antenne pour la réception en FM
– para despertarse con el zumbador a la 1ª hora de despertarse
– para despertarse con la radio a la 1ª hora de despertarse
– para apagar el despertador ALARM 1
– para despertarse con el zumbador a la 2ª hora de despertarse
– para despertarse con la radio a la 2ª hora de despertarse
– para apagar el despertador ALARM 2
– para encender (ON)/apagar (OFF) la radio
– para ajustar la iluminación del visor: HI (alto)- LOW (bajo)
– indica las horas, los minutos y los despertadores
activados
– para ajustar el reloj
– para ajustar/verificar la 2ª hora de despertarse
– para ajustar/verificar la 1ª hora de despertarse
– para que el visor vuelva a mostrar la hora del reloj después
de haber ajustado el reloj/despertador
– para ajustar las horas y los minutos (rápido hacia arriba,
lento hacia abajo) para el reloj y el despertador
– para activar el tiempo de dormitado
– para apagar el despertador activado para 24 horas
– para aumentar el nivel de bajos:
Dynamic Bass Boost
– para cancelar la función de dormitado
– para apagar el despertador activado por 7 minutos
– para sintonizar la emisora de radio deseada
– para seleccionar la banda de ondas (FM-AM)
– para ajustar el volumen
–
para la pile de respaldo
– para la conexión a la red
– antena para la FM
$
AJ3
380 A
M FM CLO
CK R
ADIO
AJ338
0 AM
FM
CL
OCK
R
ADIO
P
M
A
L
A
R
M
AL
A
R
M
F
M
M
H
z
88
• 92
• 96
•
100
• 104
• 108
M
H
z
FM
FM
M
H
z
88
• 92
•
96
• 100
• 104
• 108
M
H
z
FM
AM
k
H
z
53
0
6
3
0
8
00
1
0
0
0
1
3
0
0
1
6
00
k
H
z
AM
AM
k
H
z
5
3
0
6
30
8
0
0
1
0
00
1
30
0
1
6
0
0
k
H
z
AM
R
EPEA
T
AL
AR
M
S
L
U
M
B
E
R
•
•
•
O
F
F
A
L
A
R
M
R
ES
E
T
A
O
A
O
A
O
A
O
A
O
A
O
A
O
A
O
A
A
O
A
O
A
O
dual alarm
1
3
2
4
8
9
6
7
@
#
0
!
5
%
SAFETY INSTRUCTIONS – Read before operating equipment
This product was designed and manufactured to meet
strict quality and safety standards. There are, however,
some installation and operation precautions which you
should be particularly aware of.
1. Read Instructions - All the safety and operating
instructions should be read before the appliance is
operated.
2. Retain Instructions - The safety and operating
instructions should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in
the operating instructions should be adhered to.
4. Follow Instructions - All operating and use
instructions should be followed.
5. Water and Moisture - The appliance should not be
used near water - for example, near a bathtub,
washbowl, kitchen sink, laundry tub or swimming pool,
or in a wet basement, etc.
6. Carts and Stands - The appliance should be used
only with a cart or stand that is recommended by the
manufacturer.
6A. An appliance and cart combination should
be moved with care. Quick stops, exces-sive
force, and uneven surfaces may cause the
appliance and cart combination to overturn.
7. Wall or Ceiling Mounting - The appliance should be
mounted to a wall or ceiling only as recommended by
the manufacturer.
8. Ventilation - The appliance should be situated so that
its location or position does not interfere with its
proper ventilation. For example, the appliance should
not be situated on a bed, sofa, rug, or similar surface
that may block the ventilation openings, or, placed in a
built-in installation, such as a bookcase or cabinet that
may impede the flow of air through the ventilation
openings.
9. Heat - The appliance should be situated away from
heat sources such as radiators, heat registers, stoves,
or other appliances (including amplifiers) that produce
heat.
10.
Power Sources - The appliance should be connected
to a power supply only of the type described in the
operating instructions or as marked on the appliance.
11. Grounding or Polarization -
Precautions should be taken
so that the grounding or
polarization means of an
appliance is not defeated.
CAUTION: To
prevent electric shock, match the wide blade of this
plug to the wide slot, and fully insert. Do not use this
(polarized) plug with an extension cord, receptacle or
other outlet unless the blades can be fully inserted to
prevent blade exposure.
12. Power Cord Protection - Power supply cords should
be routed so that they are not likely to be walked on
or pinched by items placed upon or against them,
paying particular attention to cords and plugs,
convenience receptacles, and the point where they
exit from the appliance.
13. Cleaning - The appliance should be cleaned only as
recommended by the manufacturer.
14. Power Lines - An outdoor antenna should be located
away from power lines.
15. Nonuse Periods - The power cord of the appliance
should be unplugged from the outlet when left
unused for a long period of time.
16. Object and Liquid Entry
- Care should be taken so
that objects do not fall and liquids are not spilled into
the enclosure through openings.
17. Damage Requiring Service - The appliance should
be serviced by qualified service personnel when:
A. The power supply cord or the plug has been
damaged; or
B. Objects have fallen, or liquid has spilled into the
appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally
or exhibits a marked change in performance; or
E. The appliance has been dropped, or the enclosure
damaged.
18. Servicing - The user should not attempt to service
the appliance beyond that described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
WARNING
To reduce the risk of fire or electric
shock, do not expose this appliance
to rain or moisture.
The set complies with the FCC-Rules, Part
15.
91/8 EL 4562-1
Know these safety symbols
T
This bolt of lightning indicates uninsu
lated
material within your unit may caus
e an electrical
shock. For the safety of everyone in your
household, please do not remove product
covering.
S
This exclamation point calls attention to features
for which you should read the enclosed
literature closely to prevent operating and
maintenance problems.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
AC
Polarized Plug
PORTABLE
AUDIO
90 Days Free Exchange
This product must be carried in for an exchange.
WHO IS COVERED?
You must have proof of purchase to exchange the product.
A sales receipt or other document showing that you
purchased the product is considered proof of purchase.
Attach it to this owner’s manual and keep both nearby.
WHAT IS COVERED?
Warranty coverage begins the day you buy your product.
For 90 days thereafter, a defective or inoperative product
will be replaced with a new, renewed or comparable
product at no charge to you. A replacement product is
covered only for the original warranty period. When the
warranty on the original product expires, the warranty on
the replacement product also expires.
WHAT IS EXCLUDED?
Your warranty does not cover:
• labor charges for installation or setup of the product,
adjustment of customer controls on the product, and
installation or repair of antenna systems outside of the
product.
• product repair and/or part replacement because of
misuse, accident, unauthorized repair or other cause
not within the control of Philips Consumer Electronics
Company.
• reception problems caused by signal conditions or
cable or antenna systems outside the unit.
• a product that requires modification or adaptation to
enable it to operate in any country other than the
country for which it was designed, manufactured,
approved and/or authorized, or repair of products
damaged by these modifications.
• incidental or consequential damages resulting from the
product. (Some states do not allow the exclusion of
incidental or consequential damages, so the above
exclusion may not apply to you. This includes, but is
not limited to, prerecorded material, whether
copyrighted or not copyrighted.)
• a product used for commercial or institutional
purposes.
WHERE IS EXCHANGE AVAILABLE?
You may exchange the product in all countries where the
product is officially distributed by Philips Consumer
Electronics Company. In countries where Philips
Consumer Electronics Company does not distribute the
product, the local Philips service organization will attempt
to provide a replacement product (although there may be
a delay if the appropriate product is not readily available).
BEFORE REQUESTING EXCHANGE...
Please check your owner’s manual before requesting an
exchange. Adjustments of the controls discussed there may
save you a trip.
EXCHANGING A PRODUCT IN U.S.A.,
PUERTO RICO OR U.S. VIRGIN ISLANDS...
Contact your dealer to arrange an exchange. Or, ship the
product, insured and freight prepaid, and with proof of
purchase enclosed, to the address listed below.
Small Product Service Center
Philips Service Company
907 Snapps Ferry Road
Plant 2, Building 6
Greeneville, TN 37743
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied
warranties, including implied warranties of merchantability and
fitness for a particular purpose, are limited in duration to the
duration of this express warranty. But, because some states
do not allow limitations on how long an implied warranty may
last, this limitation may not apply to you.)
EXCHANGING A PRODUCT IN CANADA...
Please contact Philips at:
1-800-661-6162 (French Speaking)
1-800-363-7278 (English Speaking)
(In Canada, this warranty is given in lieu of all other
warranties. No other warranties are expressed or implied,
including any implied warranties of merchantability or
fitness for a particular purpose. Philips is not liable under
any circumstances for any direct, indirect, special,
incidental or consequential damages, howsoever incurred,
even if notified of the possibility of such damages.)
TO GET OUT-OF-WARRANTY EXCHANGE...
In U.S.A., Puerto Rico or U.S. Virgin Islands, contact Philips
Service Company at (800) 851-8885 to obtain the cost of out-
of-warranty exchange. Then carefully pack the product and
ship it to the Small Product Service Center (address listed
above). In Canada, call the phone number listed above uner
“Exchanging a Product in Canada” to obtain the cost of out-
of-warranty exchange.
REMEMBER...
Please record the model and serial numbers found on the
product below. Also, please fill out and mail your warranty
registration card promptly. It will be easier for us to notify
you if necessary.
MODEL # __________________________________
SERIAL # __________________________________
EL4966E004 / MAC 4107 / 1-97
This warranty gives you specific legal rights. You may have other rights which vary from state/province to state/province.
Philips Service Company, P.O. Box 555, Jefferson City, Tennessee 37760, (423) 475-8869
– If a fault occurs, first check the points listed below before taking the set for repair.
– If you are unable to remedy a problem by following the hints below, consult your dealer or sevice
center.
WARNING: under no circumstances should you try to repair the set yourself, as this will invalidate
the warranty.
The type-plate is located on the bottom of the clock radio.
This set complies with the FCC-Rules, part 15. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
XP AJ 3380/17 19-09-2000 12:07 Pagina 1