Filter
Top Products
IOIO
IOIO
IOIO
IOIO
IOIO
IOIO
IOIO
IOIO
OIOIOOIOIOO
OIOIOOIOIOO
OIOIOOIOIOO
OIOIOOIOIOO
FM • • • • • • 88
92 96
100 104 106
108 • • • MHz
REC • PLAY
REC • PLAY
AUTOMATIC STOP MECHANISM
•
ONE TOUCH RECORDING
DBB
dynamic bass boost
DBB
dynamic bass boost
AUTOMATIC STOP MECHANISM
•
ONE TOUCH RECORDING
IOIOOOO
OIOIIOOIOO
O
IO
OO
O
OIOIOOIOIOO
IOIOOOO
OIOIIOOIOO
O
IO
O
O
O
OIOIOOIOIOO
OIOIOOIOIOO
OIOIOOIOIOO
AM • • • • • • 540
600
700 900
1700 • • • • • KHz
1100 1300 1500
VOLUME 2
DBB 1
PAUSE $
STOP/EJ. #
F.FWD @
0 PLAY
! REW
9 RECORD
3 MODE
4 PHONES
6 TUNING
5 BAND
7 FM ST
8 MIC
(under grill)
^ AC POWER
* BATTERY
COMPARTMENT
6 x R20/UM1/D-Cells
& BEAT CUT
% VOLTAGE SELECTOR
(inside compartment)
1
A
B
C
D
1
2
3
4
5
Recording General
RECORDING
Copyright:
Recording is permissible insofar as copyright or
other rights of third parties are not infringed.
Safeguarding a cassette against erasure:
Accidental erasure can be prevented by breaking
the small tab in the top left hand corner of the
back of the cassette (See fig. 4). This protection
can be reversed with a piece of adhesive tape
placed over the same corner.
Recording
• Press EJ 9 # to open the cassette holder.
• Insert the cassette (fig. 3).
For recording you must use a NORMAL
cassette (IEC
I) on which the tabs (fig. 4) have
not been broken.
At the very beginning of the tape, no recording
will take place during the first seven seconds
when the leader tape passes the recorder
heads.
• When monitoring during recording, adjust the
sound with the controls VOLUME 2 and DBB
1. These controls do not affect the recording.
Recording from the radio
• Set the MODE selector 3 to RADIO.
• Select the waveband using the
BAND switch 5.
• Tune to the desired station using the TUNING
control 6.
• In case of FM recordings, set the
MONO/STEREO switch 3 to the desired
position.
• If during the recording of a MW/AM station, a
whistling sound is heard, this sound can be
suppressed by setting the BEAT CUT switch &
to another position.
Mono recording from the built-in microphone
• Set the MODE selector 3 to TAPE.
• Set the VOLUME control 2 to the minimum
volume level (during microphone recordings,
monitoring is not possible).
Starting and stopping the recording
• To start recording, press RECORD 0 9; PLAY
1 0 is pressed too.
– When the end of the tape is reached, the
recorder buttons are released.
• To interrupt recording, press PAUSE ; $.
• To continue recording, press PAUSE ; $ again.
• Press STOP 9 # to stop the recording before
the end of he tape. On pressing again, the
cassette holder will open.
• The set is switched off if the MODE selector
3 is in position TAPE and no buttons are
pressed.
MAINTENANCE
Cassette deck
Clean the parts indicated in fig. 5 after every 50
hours of operation or, on average, once a month.
• Open the cassette holder by pressing EJ 9 #.
• Use a cotton boll slightly moistened with
alcohol or a special head cleaning fluid.
• Press PLAY 1 0 and clean the rubber pressure
roller D (fig. 5).
• Then press PAUSE ; $ and clean the capstan
C and recording/playback heads A and B.
Cleaning of the heads A and B can also be
done by playing a cleaning cassette through
once.
Remarks
Fingerprints, dust and dirt on the set can be
removed by using a soft, clean and slightly damp
leather cloth. Do not use any cleaning agents,
since they may damage the cabinet.
Do not expose the set, batteries and cassettes to
rain, moisture, sand, or excessive heat e.g. from
heating equipment or in motor cars parked in the
sun.
Troubleshooting
PROBLEM
– POSSIBLE CAUSE
• SOLUTION
No sound
– Volume is too soft or too loud
• adjust volume
– Headphones are connected
• Disconnect headphones
– Batteries are exhausted
• Insert fresh batteries
– Batteries are incorrectly inserted
• Insert the batteries correctly
– Power cord is not securely connected
• Connect the power cord properly
Poor radio reception
– Weak radio aerial signal
• Aim the aerial for best reception:
– FM: incline and rotate telescopic aerial
– AM (MW): rotate the entire set
– Interference caused by closely located
electrical equipment like TVs, video recorders,
computers, thermostats, fluorescent lamps
(TL), engines etc.
• Keep the set away from electrical equipment
Poor cassette sound quality
– Dust and dirt on the heads, capstan or
pressure roller
• Clean the heads etc. (see Maintenance)
Recording does not work
– Cassette tab(s) are removed
• Apply a piece of adhesive tape over the
missing tab space
The type plate is located on the base of the set.
This product complies with the radio interference
requirements of the European Community.
IMPORTANT NOTES
FOR USERS IN THE U.K.
Mains plug
This apparatus is fitted with an approved
moulded 13 Amp plug. To change a fuse in
this type of plug proceed as follows:
• Remove fuse cover and fuse.
• Fix new fuse which should be a BS1362
5 Amp, A.S.T.A. or BSI approved type.
• Refit the fuse cover.
If the fitted plug is not suitable for your
socket outlets, it should be cut off and an
appropriate plug fitted in its place.
If the mains plug contains a fuse, this should
have a value of 5 Amp. If a plug without a
fuse is used, the fuse at the distribution
board should not be greater than 5 Amp.
Note: The severed plug must be disposed to
avoid a possible shock hazard should it be
inserted into a 13 Amp socket elsewhere
How to connect a plug
The wires in the mains lead are coloured
with the following code: blue = neutral (N),
brown = live (L).
As these colours may not correspond with
the colour markings identifying the terminals
in your plug, proceed as follows:
• Connect the blue wire to the terminal
marked N or coloured blue or black.
• Connect the brown wire to the terminal
marked L or coloured brown or red.
• Do not connect either wire to the earth
terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make
certain that the cord grip is clamped over the
sheath of the lead - not simply over the two
wires.
If in doubt, consult a qualified electrician.
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service center.
WARNING
Under no circumstances should you try to repair the set yourself, as this would
joid the warrenty.