Filter
Top Products
Two “AAA” size batteries are used for time/alarm backup. Insert the batteries in this unit as follows:
1. Open the Battery Compartment door aq on the bottom of the unit by sliding in direction 1, then
lifting it off in direction 2.
2. Insert two (2) “AAA” batteries into the Battery Compartment as shown. Be sure to observe the
polarity markings which are engraved inside the battery compartment. Alkaline batteries are
recommended for the longest playing time.
3. Slide the Battery Compartment door back on.
NOTES:
• The AC adapter must be disconnected from the DC IN 5V jack in order for the unit to operate on
battery power.
• Thebatteryiconwillblinkinthedisplaywhenthebatteriesarelow.
memorex.com
MA4221
User Guide
Please read these instructions completely
before operating this product
Alarm Clock
Space Saving
I’ll Wake You Up in Style
AC CONNECTION
To set or reset the actual time:
It is highly recommended to install the Memorex FM Radio + Alarm Clock App to utilize its capabilities. See the App-Enhanced
Application section later in this manual.
Regardless of the source, or if the power is on or off, you can set the time as follows:
1. Press and hold the Set Time/Sync button ak until the AM/PM indicator blinks.
2. Set the unit to standard 12 hour time or 24 hour (military) time using the Tune/Skip/Search 9 u or : W button. Then press
the Set Time/Sync button ak again; the hours will blink.
3. Set the current hour using the Tune/Skip/Search 9 u or : W button. Then press the Set Time/Sync button again ak; the
minutes will blink.
4. Set the current minutes using the Tune/Skip/Search 9 u or : W button. Then press the Set Time/Sync button again ak;
the time will be set.
To sync the iPod
®
or iPhone
®
device’s time to this unit’s time:
With the power on, connect an iPod or Phone device as shown later in this manual. Press the Set Time/Sync button ak until the current
time appears and the display blinks twice. The time will then be synced.
NOTES:
• TheSetTime/Syncbuttonwillnotsetthealarm.
• TheiPodmini,iPodphotoandiPod4thgenerationdonotsupporttheSYNCfunction.
To set the alarm:
Regardless of the source, or if the power is on or off, you can set the alarm times as follows:
1. Press and hold the Alarm On/Off button at until the alarm time blinks.
2. Set the alarm hour using the Tune/Skip/Search 9 u or : W button. Then press the Alarm On/Off button at again; the
alarm minutes will blink.
3. Set the alarm minutes using the Tune/Skip/Search 9 u or : W button. Then press the Alarm On/Off button at again; the
source icon will blink.
4. Set the desired source to wake to (iPod, Radio or Buzzer) using the Tune/Skip/Search 9 u or : W button. Then press the
Alarm On/Off button at again; the volume level will blink.
5. Set the volume using the Volume + al or – V button. Then press the Alarm On/Off button at again and the alarm will be
set. The alarm icon will appear in the display to indicate it is activated.
OPERATION
Insert the small end of the AC adapter into the DC IN 5V jack ao (located on the rear of the unit). Connect the other end to a wall
outlet having 120V AC, 60 Hz.
NOTES:
• RemoveboththeDCplugandtheAC-INplugtodisconnecttheACadapterwhennotinuse.
• OnlyusethesuppliedACadapterwhichhasthefollowingspecs:DC5V,1.2A.
LOCATION OF CONTROLS
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Warning – Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
2. Use only the size and type of batteries specified.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. A reversed battery may cause damage to
the device.
4. Do not mix different types of batteries together (e.g. Alkaline, Rechargeable and Carbon-zinc) or old batteries with fresh ones.
5. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
6. Do not try to recharge a battery not intended to be recharged; it can overheat and rupture. (Follow battery manufacturer’s directions.)
7. Remove batteries promptly if consumed.
8. Clean the battery contacts and also those of the device prior to battery installation.
BATTERY INSTALLATION
NOTES:
• Ifradioisselected,thelastfrequencywillbetuned.
• Youcanalsosyncthealarmtimesfromtheapptothisunit(seetheApp-EnhancedApplicationsection).
• IfyouselectiPod,theiPodoriPhonedevicemustbeinsertedandturnedon.
To turn the alarm off:
To turn the alarm off, simply press the Alarm On/Off button at. The alarm will turn off, but will remain set for the next day. To turn the
alarm off so it will not sound the next day, press the Alarm On/Off button at again so the alarm indicator disappears from the display.
Snooze:
While the alarm is sounding, press the Snooze/Dimmer button w. The alarm will turn back on automatically ten minutes later. If
desired, press the Snooze/Dimmer button wagainforanothertenminutesaftertheoriginalSnoozetimehasbeenreached.Youmay
repeat this process. To cancel the Snooze function, press the Alarm On/Off button at.
Sleep:
With the unit on, press the Sleep button U; “SLEEP” will blink and “10” will show in the display, which indicates the unit will turn off
after 10 minutes. Repeatedly press the Sleep button U to select the Sleep time, up to 90 minutes in 10 minute increments. After a
couple seconds, the Sleep time will disappear from the display.
NOTE: To cancel the Sleep function, repeatedly press the Sleep button until “SLEEP” disappears from the display.
Line In Jack (Rear of Unit)
Insert one end of an audio cable (not included) into the LINE OUT jack on your external audio unit and the other end into the LINE
IN jack an on the rear of this unit. To listen to the external audio unit, turn this unit on using the Power button X, and turn on
the external unit as well. Repeatedly press the SOURCE button v to select Line In mode; “line-in” will appear in the display. The
external audio unit’s output sound will be heard through this unit’s speakers. If you wish to listen to the iPod or iPhone device in the
iPod or iPhone device compartment, repeatedly press the SOURCE button v to select iPod mode; “iPod” will appear in the display.
Using an iPod or iPhone Device with this Unit
With an iPod or iPhone device connected, if this unit is not already on, turn this unit on by pressing the Power button X. Repeatedly
press the Source button v to select iPod or iPhone device mode; “iPod” will appear in the display.
YoucanoperatetheiPodoriPhonedeviceusingitsowncontrols,asperitsowner’smanual,oryoucanusethecontrolsonthis
unit to operate the iPod or iPhone device.
To play/pause the iPod or iPhone device:
Press the Play/Pause4;button x to start playback on your iPod or iPhone device. Press again to pause playback, the Pause indicator
will blink in the display; press yet again to resume playback. If you have the Shuffle and/or the Repeat option selected on your iPod
or iPhone device, the respective indicator will appear in this display.
To skip forward or backward on the iPod device: Press the Tune/Skip/Search 9 u or : W button to skip to the
beginning of the current track, previous or next track.
To search forward or backward on the iPod device: Press and hold the Tune/Skip/Search 9 u or : W button to
search within the currently-playing track.
To adjust the main volume: Press the Volume + al or – V button to increase or decrease the volume.
To turn the unit off: To turn this unit off, press the Power button X.
NOTE: After you have adjusted the volume setting, if you turn the unit off and then on again, the volume level will be set to the level
you selected prior to turning the unit off.
Using the FM Radio
It is highly recommended to install the Memorex FM Radio + Alarm Clock App so you can set FM presets, view the frequencies, and
more. See the App-Enhanced Application section later in this manual.
Turn this unit on by pressing the Power button X.
Repeatedly press the Source button v to select Radio mode; “radio” will appear in the display.
Repeatedly press the Tune/Skip/Search 9 u or : W button to manually advance the frequency up or down until the desired
frequency is playing.
For auto tuning, press and hold the Tune/Skip/Search 9 u or : W button until the frequency starts to scan, then release;
the tuner will search and then stop on the next strong station it finds. Repeat this step until the desired frequency appears in
the display.
To adjust the main volume: Press the Volume + al or – V button to increase or decrease the volume.
To turn the unit off: To turn this unit off, press the Power button X.
To change the FM region:
This unit allows you to set the desired radio region. For region details, see Radio Regions below.
• Withtheunitoff,pressand hold the Source v and Play/Pause4;x buttons simultaneously until the region number appears
in the display.
• Withinfourseconds,selectaregionusingtheTune/Skip/Search9 u or : W button.
• Whendonesetting,pressanybuttonorwaitforfiveseconds;theregionwillbeset.
RADIO REGIONS: Region 1 – United States (87.5MHz to 108MHz)
Region 2 – Europe (87.5MHz to 108MHz)
Region 3 – Japan (76MHz to 108MHz)
Dimmer: Press the Snooze/Dimmer button w to dim the display.
App-Enhanced Application
When first connected to an App-compatible device, a message may appear on the iPod or iPhone device stating an Application
isnotinstalled.ClickYESandyourdevicewilltakeyoutotheAppStoretoinstallthefreeApp,MemorexFMRadio+AlarmClock
App.Followtheonlineinstructionstoinstall.YoucanalsoinstalltheMemorexFMRadio+AlarmClockAppdirectlyfromthe
App Store.
NOTE: App requires iOS 4.0 or greater.
To use the App:
The default display is the Alarms screen. Here you can turn the alarms on or off, set Alarm 1 and/or Alarm 2, and set the source,
volume and snooze time. Press Sync to sync the alarms on the iPod or iPhone device with this unit.
Settings: Press the Settings icon to bring up the Settings display. Here you can sync clock time, toggle 12/24 hour mode, set
display brightness, and set the Sleep timer.
About: Press the About icon to view the About display, which will give you information about your unit and the latest version installed.
Audio: Press the Audio icon to bring up the Audio display. Here you can select iPod, FM, AUX or OFF. The FM function is in sync
with this unit’s FM radio and buttons. Therefore, after selecting FM you can drag the frequency on the iPod or iPhone device to the
left or right to select a frequency, or you can use this unit’s controls for the same results.
To make a preset of a frequency, simply press and hold one of the six presets until the iPod or iPhone device vibrates to memorize
the station. To recall, simply press the preset.
Note: The App is subject to change without notice and is not compatible with all iPod devices.
OPERATION (CONTINUED)
73952353-D
GENERAL:
Power Source ...............DC 5V, 1.2A Adapter (Center Positive)
Speaker . .............................................................. 1 x 4 ohm
Dimensions .................. 4.45 (W) x 3.30 (D) x 6.97 (H) inches
Made for iPod touch (2nd, 3rd and 4th generation), iPod classic, iPod nano (2nd, 3rd, 4th, 5th and
6th generation), iPhone 4S, iPhone 4, iPhone 3GS and iPhone 3G.
“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to
connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the
use of this accessory with iPod or iPhone may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
Imation Enterprises Corp.
1 Imation Way, Oakdale, MN 55128-3414 USA
© Imation Corp. www.memorex.com
Memorex and the Memorex logo are trademarks of Imation Corp and its affiliates. All other trademarks are the property of their
respective owners.
For additional setup, operating assistance or an electronic version of this user manual, please visit www.memorex.com
For consumer replaceable part(s), verify part number(s) then contact our parts and accessory fulfillment center at: 1-800-379-8439
Output Power........................................................... 1 x 0.8W
Weight ..................................................................... 0.96 lbs
Specifications are subject to change without notice.
SPECIFICATIONS AND COMPATIBILITY
1. Tune/Skip/Search 9 Button
2. Source Button
3. Snooze/Dimmer Button
4. Play/Pause4; Button
5. iPod or iPhone Device Dock
with Connector
6. Sleep Button
7. Volume – (Down) Button
8. Tune/Skip/Search : Button
9. Power Button
10. Alarm On/Off Button
11. Set Time/Sync Button
12. Volume + (Up) Button
13. Display
14. Line IN Jack
15. DC IN 5V Jack (AC ADAPTER PART
NO. 0251-211120-90003*)
16. FM Antenna
17. Battery Compartment (Bottom of unit)
(BATTERY COVER PART NO.
3052-017806-30000 *)
*Consumer Replaceable Part
(See end of guide to order.)
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
DANGEROUS VOLTAGE: The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
ATTENTION: The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized
change or modification is made.
CAUTION:TOPREVENTELECTRICSHOCK,MATCHWIDEBLADEOFPLUGTOWIDESLOTANDFULLYINSERT.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
• Theratinginformationislocatedatthebottomoftheapparatus.
1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all Instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with
the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding-type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. When
the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
15. WARNING: To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture. Do not place objects filled with water, such
as a vase, on the apparatus.
16. The AC mains plug is used as the power disconnect device and it should
remain readily accessible and operable during intended use. In order to
completely disconnect the apparatus from power, the mains plug should
be completely removed from the AC outlet socket.
17. CAUTION: To reduce the risk of fire or explosion, do not expose batteries
to excessive heat such as sunshine, fire or other heat sources.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This Class B digital apparatus complies with Canadian ICES-003.
SURGE PROTECTORS: It is recommended to use a surge protector for AC connection. Lightning and power surges ARE NOT covered under warranty for
this product.
PRECAUCIÓN: PARA REDUCIR EL RIESGO DE DESCARGA ELÉCTRICA, NO QUITE LA CUBIERTA (NI LA PARTE TRASERA). NO CONTIENE PIEZAS EN EL
INTERIOR QUE PUEDAN SER REPARADAS POR EL USUARIO. EL MANTENIMIENTO DEBE SER REALIZADO POR PERSONAL DE MANTENIMIENTO CALIFICADO.
VOLTAJE PELIGROSO: El rayo con el símbolo de la punta de flecha dentro de un triángulo equilátero tiene como objetivo advertir al
usuario acerca de la presencia de voltaje no aislado peligroso dentro de la caja del producto que puede ser de magnitud suficiente
para generar un riesgo de descarga eléctrica para las personas.
ATENCIÓN: El signo de exclamación dentro de un triángulo equilátero tiene como objetivo alertar al usuario acerca de la presencia de
instrucciones de funcionamiento y mantenimiento (servicio) importantes en la bibliografía que acompaña a la aplicación.
ADVERTENCIA DE LA FCC: ESTE EQUIPO PUEDE GENERAR O UTILIZAR ENERGÍA DE RADIO FRECUENCIA. LOS CAMBIOS O LAS MODIFICACIONES DE
ESTE EQUIPO PUEDEN PROVOCAR INTERFERENCIA PERJUDICIAL, A MENOS QUE ESTÉN EXPRESAMENTE APROBADAS EN EL MANUAL DE INSTRUCCIONES.
EL USUARIO PODRÍA PERDER LA AUTORIDAD PARA HACER FUNCIONAR ESTE EQUIPO SI REALIZA ALGÚN CAMBIO O MODIFICACIÓN NO AUTORIZADOS.
PRECAUCIÓN: PARA EVITAR DESCARGAS ELÉCTRICAS, UNA LA CLAVIJA ANCHA DEL ENCHUFE CON LA RANURA ANCHA E INSÉRTELA POR COMPLETO.
ESTE DISPOSITIVO CUMPLE CON LA PARTE 15 DE LAS REGLAS DE LA FCC (FEDERAL COMUNICATIONS COMMISSION). EL FUNCIONAMIENTO DEPENDE DE
LASDOSCONDICIONESQUESEMENCIONANACONTINUACIÓN:(1)ESTEDISPOSITIVONOCAUSAINTERFERENCIANOCIVAY(2)ESTEDISPOSITIVODEBE
ACEPTARTODAINTERFERENCIARECIBIDA,INCLUYENDOINTERFERENCIAQUEPUEDAOCASIONARUNFUNCIONAMIENTOINDESEABLE.
PRECAUCIÓN
RIESGO DE DESCARGA ELÉCTRICA
NO ABRIR
1. Lea estas instrucciones.
2. Conserve estas instrucciones.
3. Preste atención a todas las advertencias.
4. Siga todas las instrucciones.
5. No utilice este aparato cerca de agua.
6. Limpie sólo con un paño seco.
7. No bloquee ninguna de las aberturas de ventilación. Instale el
producto de acuerdo con las instrucciones del fabricante.
8. No instale el producto cerca de fuentes de calor, como radiadores,
rejillas de calefacción, estufas u otros aparatos (incluidos los
amplificadores) que generen calor.
9. No rechace el objetivo de seguridad del enchufe polarizado o de
conexión a tierra. Un enchufe polarizado tiene dos clavijas: una más
ancha que la otra. Un enchufe de conexión a tierra posee dos clavijas
y una tercera prolongación de conexión a tierra. La clavija ancha y
la tercera clavija se proporcionan para su seguridad. Si el enchufe
proporcionado no encaja en su tomacorriente, comuníquese con un
electricista para reemplazar el tomacorriente obsoleto.
10. Proteja el cable de alimentación de pisadas o pinchaduras, en
particular en los enchufes, los tomacorrientes y el punto de donde
salen del aparato.
11. Utilice sólo dispositivos/accesorios especificados por el fabricante.
12. Use sólo el carro, el pie, el trípode, el soporte o la mesa especificados
por el fabricante o que se vendan con el aparato. Cuando se utilice un
carro, tenga cuidado al mover la combinación
de carro y aparato para evitar lesiones por
caídas.
13. Desconecte el aparato durante las tormentas
eléctricas o cuando no se utilice durante un
período prolongado.
14. El mantenimiento debe ser llevado a cabo por
personal de mantenimiento calificado. Se requiere mantenimiento
si el aparato se dañó de alguna forma; por ejemplo, si se derramó
líquido o cayeron objetos dentro del aparato, si se expuso a la lluvia o
a la humedad, si se cayó, si no funciona normalmente o si se dañó el
cable de alimentación o el enchufe.
15. ADVERTENCIA: Para reducir el riesgo de incendio o descarga eléctrica,
no exponga este aparato a la lluvia o a la humedad. No coloque
objetos con líquidos (p. ej., jarrones) sobre el aparato.
16. El cable de alimentación de CA es el dispositivo para desconectar la
corriente; por lo tanto, debe estar al alcance de la mano y se debe
poder manejar durante el uso previsto. Para desconectar el aparato de
la corriente, el cable de alimentación se debe quitar completamente
del tomacorriente de CA.
17. PRECAUCIÓN: Para reducir el riesgo de incendio o explosión, no
exponga las pilas a calor excesivo, como la luz solar directa, el fuego
u otras fuentes de calor.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
MISE EN GARDE : POUR RÉDUIRE LES RISQUES DE CHOC ÉLECTRIQUE, NE PAS RETIRER LE COUVERCLE (OU L’ARRIÈRE). AUCUNE PIÈCE À L’INTÉRIEUR
NE PEUT ÊTRE RÉPARÉE PAR L’UTILISATEUR. CONFIEZ TOUTE RÉPARATION À UN TECHNICIEN QUALIFIÉ.
TENSION DANGEREUSE : L’éclair avec le symbole de la pointe de flèche dans un triangle équilatéral est destiné à alerter l’utilisateur
de la présence de tension dangereuse non isolée dans le boîtier du produit. Elle peut être suffisamment importante pour constituer un
risque de décharge électrique pour les personnes à proximité.
ATTENTION : Le point d’exclamation dans un triangle équilatéral est destiné à alerter l’utilisateur de la nécessité de respecter les
consignes d’utilisation et de maintenance (réparation) fournies dans la documentation qui accompagne l’appareil.
AVERTISSEMENT DE LA FCC : CET APPAREIL PEUT GÉNÉRER OU UTILISER DE L’ÉNERGIE DE RADIOFRÉQUENCE. TOUT CHANGEMENT OU MODIFICATION
DE CET APPAREIL PEUT ENTRAÎNER DES INTERFÉRENCES NUISIBLES À MOINS QUE LES MODIFICATIONS NE SOIENT EXPRESSÉMENT APPROUVÉES DANS
LE GUIDE D’UTILISATION. L’UTILISATEUR RISQUE LE RETRAIT DE L’AUTORISATION D’UTILISER CET ÉQUIPEMENT SI UNE MODIFICATION OU UN CHANGEMENT
NON AUTORISÉ EST EFFECTUÉ.
MISE EN GARDE : POUR ÉVITER TOUT RISQUE DE CHOC ÉLECTRIQUE, INSÉREZ À FOND LA LAME LA PLUS LARGE DANS L’ORIFICE LE PLUS LARGE DE
LA PRISE.
CET APPAREIL EST CONFORME À LA SECTION 15 DES RÈGLEMENTS DE LA FCC. LE FONCTIONNEMENT EST SOUMIS AUX DEUX CONDITIONS SUIVANTES
:(1)CEDISPOSITIFN’ESTPASCENSÉCAUSERD’INTERFÉRENCESNUISIBLES,ET(2)CEDISPOSITIFDOITRECEVOIRTOUTEINTERFÉRENCE,YCOMPRIS
CELLES POUVANT CAUSER UN FONCTIONNEMENT NON DÉSIRÉ.
MISE EN GARDE
RISQUE DE CHOC ÉLECTRIQUE NE
PAS OUVRIR
REMARQUE : Cet appareil a été testé et approuvé comme étant conforme aux limites préconisées pour un appareil numérique de la classe B
conformément à la section 15 des réglementations de la FCC. Ces limites sont conçues pour fournir une bonne protection contre les interférences nuisibles
dans une installation domestique. Cet appareil génère, utilise et peut émettre de l’énergie de radiofréquence et, s’il n’est pas installé et utilisé conformément
aux instructions, peut perturber les communications radio. Cependant, il n’existe aucune garantie quant à l’absence d’interférences dans une installation
particulière. Si cet appareil cause des interférences nuisibles au niveau de la réception radio ou de la télévision, (ce qui peut être vérifié en l’allumant et en
l’éteignant), l’utilisateur doit essayer de remédier au problème en prenant les mesures suivantes :
• Réorientezourepositionnezl’antenneréceptrice.
• Augmentezladistancequiséparel’appareildurécepteur.
• Connectezl’appareilàuneprisesuruncircuitdifférentdeceluiutiliséparlerécepteur.
• Consultezlerevendeurouuntechnicienradio/téléviseurexpérimenté.
• Laplaquesignalétiqueestapposéesousl’appareil.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
PARASURTENSEURS : IL EST RECOMMANDÉ D’UTILISER UN PARASURTENSEUR POUR LE BRANCHEMENT SUR COURANT ALTERNATIF. LES DÉGÂTS DUS À
LA FOUDRE ET AUX SURTENSIONS NE SONT PAS COUVERTS PAR LA GARANTIE QUI ACCOMPAGNE CE PRODUIT.
Lisez ces consignes.
2. Conservez ces consignes.
3. Tenez compte de tous les avertissements.
4. Suivez toutes les consignes.
5. N’utilisez pas cet appareil à proximité de l’eau.
6. Nettoyez uniquement avec un chiffon sec.
7. Ne bouchez pas les orifices prévus pour la ventilation. Installez
conformément aux instructions du fabricant.
8. N’installez pas l’appareil à proximité de sources de chaleur telles que
les radiateurs, les grilles de chauffage, les cuisinières ou d’autres
appareils (y compris les amplificateurs) qui génèrent de la chaleur.
9. Ne supprimez en aucun cas la fonctionnalité de sécurité de la fiche
polarisée ou avec mise à la terre. Une fiche polarisée comporte deux
lames avec une plus large que l’autre. Une fiche avec mise à la terre a
deux lames et une troisième broche de mise à la terre. La lame large
ou la troisième broche ont été prévues pour votre sécurité. Si vous ne
parvenez pas à brancher la fiche fournie dans votre prise, consultez
un électricien afin qu’il remplace la prise obsolète.
10. Protégez le cordon d’alimentation pour qu’il ne soit pas piétiné ou
pincé en particulier au niveau des fiches, des prises de courant et à
l’endroit où il sort de l’appareil.
11. Utilisez uniquement les fixations ou les accessoires recommandés par
le fabricant.
12. Utilisez uniquement avec un chariot, un pied, un trépied, un support
ou une table recommandé(e) par le fabricant ou vendu(e) avec
l’appareil. Si un chariot est utilisé, déplacez prudemment l’ensemble
appareil et chariot pour éviter des blessures
causées par un basculement.
13. Débranchez cet appareil pendant les orages ou
si vous prévoyez de ne pas l’utiliser pendant
une longue période.
14. Confiez toute réparation à du personnel
qualifié. Une réparation est nécessaire si
l’appareil a été endommagé de quelconque
manière, par ex. si le câble ou la fiche d’alimentation est abîmé(e), ou
du liquide a été renversé ou si des objets sont tombés dans l’appareil,
ou encore si ce dernier a été exposé à la pluie ou à l’humidité, ne
fonctionne pas normalement, ou est tombé.
15. AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc
électrique, n’exposez pas cet appareil à la pluie ni à l’humidité. Aucun
objet contenant du liquide, comme un vase, ne doit être posé sur
l’appareil.
16. La fiche secteur est utilisée comme dispositif de mise hors tension
et doit rester aisément accessible et fonctionnelle à tout moment
pendant l’utilisation prévue. Pour mettre l’appareil totalement hors
tension, retirez complètement la fiche de la prise secteur.
17. MISE EN GARDE : Pour réduire le risque d’incendie ou d’explosion,
n’exposez pas les piles à une chaleur intense, par exemple au soleil,
au feu ou à d’autres sources
de chaleur.
IMPORTANTES CONSIGNES DE SÉCURITÉ
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NOTA: Este equipo ha sido probado y cumple con los límites correspondientes a un dispositivo digital Clase B, según la parte 15 de las Normas de FCC.
Estos límites están diseñados para proporcionar una protección razonable contra la interferencia dañina en una instalación residencial. Este equipo genera,
utiliza y puede irradiar energía de radiofrecuencia y, si no se instala y usa de acuerdo con las instrucciones, puede generar interferencia perjudicial en
las comunicaciones de radio. Sin embargo, no se garantiza que la interferencia no se produzca en una instalación en particular. Si este equipo genera
interferencia perjudicial en la recepción de radio o televisión, que puede determinarse encendiendo y apagando el equipo, se recomienda al usuario que
intente corregir la interferencia mediante una o más de las siguientes medidas:
• Vuelvaaorientaroubicarlaantenareceptora.
• Aumentelaseparaciónentreelequipoyelreceptor.
• Conecteelequipoauntomacorrientedeuncircuitodistintodelqueestáconectadoelreceptor.
• ConsulteconeldistribuidoroconuntécnicoderadiooTVexperimentadoparaobtenerasistencia.
• Lainformacióndeclasificaciónseencuentraenlaparteinferiordelaparato
ADVERTENCIA: PARA EVITAR EL RIESGO DE INCENDIO O DESCARGA, NO EXPONGA ESTA UNIDAD A LA LLUVIA O LA HUMEDAD.
Este aparato digital Clase B cumple con la norma canadiense ICES-003.
PROTECTORES CONTRA SOBRETENSIÓN: SE RECOMIENDA UTILIZAR UN PROTECTOR CONTRA SOBRETENSIÓN PARA LA CONEXIÓN DE CA. LOS CASOS
DESOBRETENSIÓNDEENERGÍAYRAYOSNOESTÁNCUBIERTOSPORLAGARANTÍADEESTEPRODUCTO.
AVERTISSEMENT : POUR ÉVITER TOUT RISQUE D’INCENDIE OU DE DÉCHARGE ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL
À LA PLUIE OU À L’HUMIDITÉ.
1
2
AAA
Front of unit
AAA
2
1
3
4
11
12
13
10
9
8
5
6
7
15
16
17
14