Filter
Top Products
Additional Features
27
UDP-89 User Manual Version 2.0 www.hhb.co.uk
Storing and Cueing to a Marker Point
The UDP-89 has a “scratchpad” location memory, which can be
used to store a marker point in programme material “on-the-fly”.
The marker point can easily be recalled and located to at a later
time.
The feature is entered by
pressing the CUE button (either
on the front panel
or the
remote control unit) while a disc
is playing, which causes the
front panel display and the pop-
up window below to be shown.
C03 0:01:15
Cue
DVD- V
Bookmark --:--:--
C03 0:02:08
Cue
0:01:18
C03 0:02:08
Cue
Chap 03
Bookmark 00:01:18
Initially, the Cue memory is empty. Note that the wording in the
pop-up window changes slightly with other disc types.
Storing a Marker point:
Pressing MARK/ENTER while the Cue memory is displayed
will store the playback location at that instant into the memory.
This is confirmed by the MARK flag in the front panel display.
The time saved into memory is displayed both on-screen and on
the front panel, see above. Note that the track/chapter number
is also displayed on the front panel with an alternating display.
The current play point can only be stored if the memory is
empty. Pressing it when the memory already contains a valid
time will cause the disc to locate to that point (see next section).
Thus marking a point during audition and then subsequently
relocating back to it requires only two keystrokes.
A further press of the CUE button cancels the displays; the
contents of the memory remains saved as long as the disc
remains loaded.
Locating to the Marker point:
Press CUE to open the Cue pop-up window, and press MARK/
ENTER. The disc will immediately locate to the Cue point and
play from there (unless Auto-Pause Mode is enabled; see next
section). The pop-up window closes.
Note: The time loaded into the memory includes the track
number (in the case of CDs) as well as the Track Time, though
only the Track Time is displayed. The CUE feature may be
used to re-locate to a point within a different CD track to that
currently playing. In the case of DVDs, the overall disc time is
stored.
Clearing the memory:
Pressing CLR (on the remote control unit) or either the LEFT
or RIGHT front-panel cursor keys while the Cue window is
on-screen will clear the contents of the memory. The front panel
display shows Cue Cleared in confirmation and the MARK flag
extinguishes. Unless cleared, a Marker point remains stored
until the disc is removed from the unit.
Auto-Pause
The UDP-89’s Auto-Pause Mode allows accurate cueing to the
start of a track (CDs) or chapter (DVDs). The transport enters
Pause Mode at the start of the track/chapter, awaiting a PLAY
command.
Auto-Pause Mode is enabled by
pressing the A-PAUSE button on
the front panel
or remote
control unit. The selection is
confirmed by the A.PAUSE flag
in the front-panel display.
When Auto-Pause Mode is enabled, the unit will enter Pause
Mode automatically after a re-location to a different disc location
has been commanded by any method, including:
usingtheNEXTorPREVIOUSkeystostepthroughdisk•
tracks/chapters
useoftheUP/DOWNcursorkeyswithCDstostep•
through the on-screen track list display
locationtoadifferenttrack/chapterwiththeremote•
control unit’s 0-9 keys
useoftheSearchfunction•
useoftheCue(Bookmark)function•
Hint: If held in Pause Mode at the start of a track or chapter,
playback may restart more accurately if the ENTER button is
used instead of PLAY. If the GUI is being used, the cursor must
be positioned on the relevant track.