Filter
Top Products
To set the alarm:
1 Press and hold either the ALM 1 or ALM 2 button for approximately two
seconds. The hour digit will ash.
2 Press the TUNE+ or TUNE– button to set the hour, then press the ALM 1 or
ALM 2 button to save your setting. The minutes digits will ash.
3 Press the TUNE+ or TUNE– button to set the minutes, then press the ALM
1 or ALM 2 button to save your setting.
4 Press the ALM 1 or ALM 2 button again to conrm the setting. When the
alarm time is reached, the alarm sounds.
5 To use the snooze feature, press the SNOOZE button. The alarm turns o for
nine minutes, then turns on again.
6 To turn the alarm completely o, press any button except the SNOOZE
button.
To wake to radio or alarm:
1 Conrm the Clock time setting by quickly pressing and releasing the ALM1
or ALM 2 button. The alarm time and source are displayed on the display.
2 To switch between the buzzer and radio alarm, quickly press ALM1 or ALM
2 repeatedly, until the alarm source you want is displayed on the display.
To use the radio:
1 Press and hold the RADIO/ON/OFF/ button more than two seconds to
turn your clock radio on.
2 Press the TUNE+ or TUNE– button to tune to the radio station you want.
3 Press and hold TUNE+ or TUNE– button more than two seconds, then
release the button to start the FM radio station scan.
To preset radio stations:
1 Tune to the station you want to preset.
2 Press and hold the PRESET/MEM button for over two seconds. “P01” ashes
on the display.
3 Press TUNE+ or TUNE– to select the preset number you want to assign to
the station.
4 Press the PRESET/MEM button to store the setting.
5 Repeat the previous steps to preset additional stations. You can preset as
many as 20 stations.
6 To tune to a preset station, quickly press and release the PRESET/MEM button
one or more times until the preset number you want appears in the display.
To set the sleep timer:
1 Press the SLEEP button one or more times to select the amount of time you
want the radio to play before it turns o. You can select 15, 30, 45, 60, or
90 minutes. When the sleep timer is set, zzZ appears on the display.
2 To cancel the sleep timer, press the SLEEP button one or more times until
OFF appears on the display.
ENGLISH 11-0019
To lock or unlock the buttons:
• Quickly press the RADIO/ON/OFF/ button twice. The presses must be
within one second of each other. When the buttons are locked (disabled),
LOC is displayed on the display. When the buttons are unlocked (enabled),
LOC disappears from the display.
Safety information
WARNING: Batteries should not be exposed to excessive heat such as sunshine, re, or the
like. RISK OF EXPLOSION IF BATTERIES ARE REPLACED BY AN INCORRECT TYPE. DISPOSE OF
USED BATTERIES ACCORDING TO THE INSTRUCTIONS
WARNING: To avoid dangerous radiation exposure, do not try to perform any operations not
covered in these instructions.
WARNING: To prevent re or shock hazard, do not expose the the clock radio to rain or
moisture. Do not expose the apparatus to dripping or splashing. Do not place objects lled
with liquid, such as vases, on the apparatus.
WARNING: To avoid electrical shock, do not open the cabinet. Refer servicing to qualied
personnel only.
FCC statement
This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measure:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
Warning: Changes or modications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
ICES‐003 statement
This Class B digital apparatus complies with Canadian ICES‐003.
90 days limited warranty
Visit www.dynexproducts.com for details.
Contact Dynex
For customer service, call 800-305-2204
www.dynexproducts.com
© 2011 BBY Solutions, Inc. All Rights Reserved.
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and brand
names are trademarks of their respective owners.